对Socket CAN的理解（4）——【Socket CAN接收数据流程】
转载请注明出处：http://blog.csdn.net/Righthek 谢谢！
如今我们来分析一下CAN总线的接收数据流程，对于网络设备。数据接收大体上採用中断+NAPI机制进行数据的接收。相同。我们如今的CAN模块也是採用相同的方式进行数据的接收。
因为我们仅仅针对CAN总线接收数据这条主线进行分析。
因些。会忽略一些针对CAN协议的设置及初始化等相关代码。
在初始化CAN设备时，我们须要给CAN设备分配NAPI功能。我们通过netif_napi_add()函数将CAN设备加入到NAPI机制列表中。源代码例如以下：
struct net_device *alloc_d_can_dev(intnum_objs)
{
structnet_device *dev;
structd_can_priv *priv;
dev= alloc_candev(sizeof(struct d_can_priv), num_objs/2);
if(!dev)
returnNULL;
priv= netdev_priv(dev);
netif_napi_add(dev, &priv->napi,d_can_poll, num_objs/2);
priv->dev= dev;
priv->can.bittiming_const= &d_can_bittiming_const;
priv->can.do_set_mode= d_can_set_mode;
priv->can.do_get_berr_counter= d_can_get_berr_counter;
priv->can.ctrlmode_supported= (CAN_CTRLMODE_LOOPBACK |
CAN_CTRLMODE_LISTENONLY|
CAN_CTRLMODE_BERR_REPORTING|
CAN_CTRLMODE_3_SAMPLES);
returndev;
}
以上将CAN设备加入到NAPI机制列表中后。那么怎样去调用它呢？（关于NAPI机制，请查看文章《以前的足迹——对CAN驱动中的NAPI机制的理解》）接下来就是中断做的事情了。在中断处理函数d_can_isr中，我们通过napi_schedule()函数调度已经在NAPI机制列表中的d_can_poll()函数。
该函数会通过轮询的方式接收数据。
而依据NAPI机制，其中断产生后，会调度轮询机制同一时候关闭全部的中断。流程例如以下图：
static irqreturn_t d_can_isr(intirq, void *dev_id)
{
structnet_device *dev = (struct net_device *)dev_id;
structd_can_priv *priv = netdev_priv(dev);
priv->irqstatus= d_can_read(priv, D_CAN_INT);
if(!priv->irqstatus)
returnIRQ_NONE;
/*disable all interrupts and schedule the NAPI */
d_can_interrupts(priv,DISABLE_ALL_INTERRUPTS);
napi_schedule(&priv->napi);
returnIRQ_HANDLED;
}
其中断产生时。会调用下面函数d_can_poll()。该函数即採用轮询的方式进行数据的接收。因为CAN总线状态中断具有最高优先权。在接收数据之前，须要对CAN总线的状态进行推断。而对于CAN总线错误状态有三种：
（1） 主动错误。
（2） 被动错误。
（3） 总线关闭；
static int d_can_poll(structnapi_struct *napi, int quota)
{
intlec_type = 0;
intwork_done = 0;
structnet_device *dev = napi->dev;
structd_can_priv *priv = netdev_priv(dev);
if(!priv->irqstatus)
gotoend;
/*status events have the highest priority */
if(priv->irqstatus == STATUS_INTERRUPT) {
priv->current_status= d_can_read(priv, D_CAN_ES);
/*handle Tx/Rx events */
if(priv->current_status & D_CAN_ES_TXOK)
d_can_write(priv,D_CAN_ES,
priv->current_status& ~D_CAN_ES_TXOK);
if(priv->current_status & D_CAN_ES_RXOK)
d_can_write(priv,D_CAN_ES,
priv->current_status& ~D_CAN_ES_RXOK);
/*handle state changes */
if((priv->current_status & D_CAN_ES_EWARN) &&
(!(priv->last_status& D_CAN_ES_EWARN))) {
netdev_dbg(dev,"entered error warning state\n");
work_done+= d_can_handle_state_change(dev,
D_CAN_ERROR_WARNING);
}
if((priv->current_status & D_CAN_ES_EPASS) &&
(!(priv->last_status& D_CAN_ES_EPASS))) {
netdev_dbg(dev,"entered error passive state\n");
work_done+= d_can_handle_state_change(dev,
D_CAN_ERROR_PASSIVE);
}
if((priv->current_status & D_CAN_ES_BOFF) &&
(!(priv->last_status& D_CAN_ES_BOFF))) {
netdev_dbg(dev,"entered bus off state\n");
work_done +=d_can_handle_state_change(dev,
D_CAN_BUS_OFF);
}
/*handle bus recovery events */
if((!(priv->current_status & D_CAN_ES_BOFF)) &&
(priv->last_status& D_CAN_ES_BOFF)) {
netdev_dbg(dev,"left bus off state\n");
priv->can.state= CAN_STATE_ERROR_ACTIVE;
}
if((!(priv->current_status & D_CAN_ES_EPASS)) &&
(priv->last_status& D_CAN_ES_EPASS)) {
netdev_dbg(dev,"left error passive state\n");
priv->can.state= CAN_STATE_ERROR_ACTIVE;
}
priv->last_status= priv->current_status;
/*handle lec errors on the bus */
lec_type= d_can_has_handle_berr(priv);
if(lec_type)
work_done+= d_can_handle_bus_err(dev, lec_type);
}else if ((priv->irqstatus >= D_CAN_MSG_OBJ_RX_FIRST) &&
(priv->irqstatus<= D_CAN_MSG_OBJ_RX_LAST)) {
/*handle events corresponding to receive message objects */
work_done+= d_can_do_rx_poll(dev, (quota - work_done));
}else if ((priv->irqstatus >= D_CAN_MSG_OBJ_TX_FIRST) &&
(priv->irqstatus<= D_CAN_MSG_OBJ_TX_LAST)) {
/*handle events corresponding to transmit message objects */
d_can_do_tx(dev);
}
end:
if(work_done < quota) {
napi_complete(napi);
/*enable all IRQs */
d_can_interrupts(priv,ENABLE_ALL_INTERRUPTS);
}
returnwork_done;
}
当总线状态数据状态正常时，进行数据的接收。
static int d_can_do_rx_poll(structnet_device *dev, int quota)
{
structd_can_priv *priv = netdev_priv(dev);
unsignedint msg_obj, mctrl_reg_val;
u32num_rx_pkts = 0;
u32intpnd_x_reg_val;
u32intpnd_reg_val;
for(msg_obj = D_CAN_MSG_OBJ_RX_FIRST; msg_obj <= D_CAN_MSG_OBJ_RX_LAST
&"a > 0; msg_obj++) {
intpnd_x_reg_val= D_CAN_GET_XREG_NUM(priv, D_CAN_INTPND_X);
intpnd_reg_val= d_can_read(priv,
D_CAN_INTPND(intpnd_x_reg_val));
/*
* as interrupt pending register's bit n-1corresponds to
* message object n, we need to handle the sameproperly.
*/
if(intpnd_reg_val & (1 << (msg_obj - 1))) {
d_can_object_get(dev,D_CAN_IF_RX_NUM, msg_obj,
D_CAN_IF_CMD_ALL&
~D_CAN_IF_CMD_TXRQST);
mctrl_reg_val= d_can_read(priv,
D_CAN_IFMCTL(D_CAN_IF_RX_NUM));
if(!(mctrl_reg_val & D_CAN_IF_MCTL_NEWDAT))
continue;
/*read the data from the message object */
d_can_read_msg_object(dev, D_CAN_IF_RX_NUM,
mctrl_reg_val);
if(mctrl_reg_val & D_CAN_IF_MCTL_EOB)
d_can_setup_receive_object(dev,D_CAN_IF_RX_NUM,
D_CAN_MSG_OBJ_RX_LAST,0, 0,
D_CAN_IF_MCTL_RXIE| D_CAN_IF_MCTL_UMASK
|D_CAN_IF_MCTL_EOB);
if(mctrl_reg_val & D_CAN_IF_MCTL_MSGLST) {
d_can_handle_lost_msg_obj(dev,D_CAN_IF_RX_NUM,
msg_obj);
num_rx_pkts++;
quota--;
continue;
}
if(msg_obj < D_CAN_MSG_OBJ_RX_LOW_LAST)
d_can_mark_rx_msg_obj(dev,D_CAN_IF_RX_NUM,
mctrl_reg_val,msg_obj);
else if (msg_obj >D_CAN_MSG_OBJ_RX_LOW_LAST)
/*activate this msg obj */
d_can_activate_rx_msg_obj(dev,D_CAN_IF_RX_NUM,
mctrl_reg_val,msg_obj);
elseif (msg_obj == D_CAN_MSG_OBJ_RX_LOW_LAST)
/*activate all lower message objects */
d_can_activate_all_lower_rx_msg_objs(dev,
D_CAN_IF_RX_NUM,mctrl_reg_val);
num_rx_pkts++;
quota--;
}
}
returnnum_rx_pkts;
}
下面函数是从CAN模块的接收寄存器中接收数据。
static int d_can_read_msg_object(structnet_device *dev, int iface, int ctrl)
{
inti;
u32dataA = 0;
u32dataB = 0;
unsignedint arb_val;
unsignedint mctl_val;
structd_can_priv *priv = netdev_priv(dev);
structnet_device_stats *stats = &dev->stats;
structsk_buff *skb;
structcan_frame *frame;
skb= alloc_can_skb(dev, &frame);
if(!skb) {
stats->rx_dropped++;
return-ENOMEM;
}
frame->can_dlc= get_can_dlc(ctrl & 0x0F);
arb_val= d_can_read(priv, D_CAN_IFARB(iface));
mctl_val= d_can_read(priv, D_CAN_IFMCTL(iface));
if(arb_val & D_CAN_IF_ARB_MSGXTD)
frame->can_id= (arb_val & CAN_EFF_MASK) | CAN_EFF_FLAG;
else
frame->can_id= (arb_val >> 18) & CAN_SFF_MASK;
if(mctl_val & D_CAN_IF_MCTL_RMTEN)
frame->can_id|= CAN_RTR_FLAG;
else{
dataA= d_can_read(priv, D_CAN_IFDATA(iface));
dataB= d_can_read(priv, D_CAN_IFDATB(iface));
for(i = 0; i < frame->can_dlc; i++) {
/*Writing MO higher 4 data bytes to skb */
if(frame->can_dlc <= 4)
frame->data[i]= dataA >> (8 * i);
else{
if(i < 4)
frame->data[i]= dataA >> (8 * i);
else
frame->data[i] = dataB >> (8 *(i-4));
}
}
}
netif_receive_skb(skb);
stats->rx_packets++;
stats->rx_bytes+= frame->can_dlc;
return0;
}
以上是对底层CAN接收数据的分析，并没有涉及到用户空间的调用。
转载请注明出处：http://blog.csdn.net/Righthek 谢谢！
