按2次增加一个num:

#include "stm32f10x.h"
#include "Delay.h"
#include "OLED.h"

int main(void)
{
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB, ENABLE);
    GPIO_InitTypeDef GPIO_InitStructure;
    GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_Out_PP;
    GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_4| GPIO_Pin_5;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure);
	
    GPIO_InitTypeDef GPIO_InitStructure0;
    GPIO_InitStructure0.GPIO_Mode  = GPIO_Mode_IPU;
    GPIO_InitStructure0.GPIO_Pin   = GPIO_Pin_0;
    GPIO_InitStructure0.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure0);
	
		GPIO_InitTypeDef GPIO_InitStructure1;
    GPIO_InitStructure1.GPIO_Mode  = GPIO_Mode_Out_OD;
    GPIO_InitStructure1.GPIO_Pin   = GPIO_Pin_8| GPIO_Pin_9;
    GPIO_InitStructure1.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOB, &GPIO_InitStructure1);
		
		OLED_Init();
		uint8_t num = 0;
		uint8_t con = 0;
		OLED_ShowString(1,1,"Num:");
		OLED_ShowNum(2,1,num,5);
		while(1){
			uint8_t key = GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0); /* 按键读取,存的是过去的值 */
			if(key == 0){
				Delay_ms(20);
				while(GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0)==0);/* 要求现取,在检查本身,按下去的状态会一直卡在while循环里,放开才会跳出循环继续往下 */
				Delay_ms(20);
				if(con%2 == 0){
					num += 1;
				}
				con+=1;
				
				OLED_ShowNum(2,1,num,5);
				uint8_t led = GPIO_ReadOutputDataBit(GPIOA,GPIO_Pin_5);
				GPIO_WriteBit(GPIOA,GPIO_Pin_5,(BitAction)(1-led));
			}
		}
}

 

按一下oled数字+=1,灯亮/灭:

#include "stm32f10x.h"
#include "Delay.h"
#include "OLED.h"

int main(void)
{
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB, ENABLE);
    GPIO_InitTypeDef GPIO_InitStructure;
    GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_Out_PP;
    GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_4| GPIO_Pin_5;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure);
	
    GPIO_InitTypeDef GPIO_InitStructure0;
    GPIO_InitStructure0.GPIO_Mode  = GPIO_Mode_IPU;
    GPIO_InitStructure0.GPIO_Pin   = GPIO_Pin_0;
    GPIO_InitStructure0.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure0);
	
		GPIO_InitTypeDef GPIO_InitStructure1;
    GPIO_InitStructure1.GPIO_Mode  = GPIO_Mode_Out_OD;
    GPIO_InitStructure1.GPIO_Pin   = GPIO_Pin_8| GPIO_Pin_9;
    GPIO_InitStructure1.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOB, &GPIO_InitStructure1);
		
		OLED_Init();
		uint8_t num = 0;
		OLED_ShowString(1,1,"Num:");
		OLED_ShowNum(2,1,num,5);
		while(1){
			uint8_t key = GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0); /* 按键读取,存的是过去的值 */
			if(key == 0){
				Delay_ms(20);
				while(GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0)==0);/* 要求现取,在检查本身,按下去的状态会一直卡在while循环里,放开才会跳出循环继续往下 */
				Delay_ms(20);
				num+=1;
				
				OLED_ShowNum(2,1,num,5);
				uint8_t led = GPIO_ReadOutputDataBit(GPIOA,GPIO_Pin_5);
				GPIO_WriteBit(GPIOA,GPIO_Pin_5,(BitAction)!led);
			}
		}
}

按键+光敏+唱歌:

#include "stm32f10x.h"
#include "Delay.h"

#define DO 262
#define RE 294
#define MI 330
#define FA 349
#define SOL 392
#define LA 440
#define SI 494
#define SOL_L 196
#define DO_H  523




void Beep(uint16_t freq, uint16_t ms)
{
    uint32_t half_us = 500000 / freq;      
    uint32_t cycles  = (uint32_t)freq * ms / 1000;  
    for (uint32_t i = 0; i < cycles; i++)
    {
        GPIO_SetBits(GPIOA, GPIO_Pin_4);
        Delay_us(half_us);
        GPIO_ResetBits(GPIOA, GPIO_Pin_4);
        Delay_us(half_us);
    }
}

int main(void)
{
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
    GPIO_InitTypeDef GPIO_InitStructure;
    GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_Out_PP;
    GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_4| GPIO_Pin_5;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure);
	
    GPIO_InitTypeDef GPIO_InitStructure0;
    GPIO_InitStructure0.GPIO_Mode  = GPIO_Mode_IPU; 
    GPIO_InitStructure0.GPIO_Pin   = GPIO_Pin_0;
    GPIO_InitStructure0.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure0);
	
    Beep(DO, 400);  Beep(RE, 400);  Beep(MI, 400);  Beep(FA, 400);
    Beep(SOL, 400); Beep(LA, 400);  Beep(SI, 400);

		
		uint16_t tune[] = {
			SOL_L, DO,                                  /*   : 5, 1 */
			RE, RE, FA, SOL, SOL, DO_H,                 /* 2 2 4 5 5 1' */
			SOL, SOL, FA, RE, SOL, SOL,                 /* 5 5 4 2 5 5 */
			RE, SOL, SOL, RE, DO,                       /* 2 5 5 2 1 */
			SOL_L, SOL_L, DO,                           /* 5,- 5, 1 */
			RE, RE, FA, SOL, SOL, DO_H,
			SOL, SOL, FA, RE, SOL, SOL,
			RE, SOL, SOL, RE, DO,
			RE, SOL, DO_H                               /* 2 - 5 1' */
		};
		uint16_t beat[] = {
			400, 400,
			400, 200, 200, 400, 200, 200,
			400, 200, 200, 400, 200, 200,
			400, 200, 200, 400, 400,
			800, 200, 200,
			400, 200, 200, 400, 200, 200,
			400, 200, 200, 400, 200, 200,
			400, 200, 200, 400, 400,
			1200, 200, 200
		};
		uint8_t len = sizeof(tune) / sizeof(tune[0]);
		uint8_t light_last = 1;                     
		
		
    while (1) {
			uint8_t light = GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_0);
			GPIO_WriteBit(GPIOA, GPIO_Pin_5, (BitAction)light);  

			if (light_last == 1 && light == 0) {                 
				for (int i = 0; i < len; i++) {
					Beep(tune[i], beat[i]);
					Delay_ms(60);
				}
				light = GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_0); 
			}
			light_last = light;
		}
}

 

按键蜂鸣

#include "stm32f10x.h"



int main(void)
{
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
    GPIO_InitTypeDef GPIO_InitStructure;
    GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_Out_PP;
    GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_4| GPIO_Pin_5;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure);
	
    GPIO_InitTypeDef GPIO_InitStructure0;
    GPIO_InitStructure0.GPIO_Mode  = GPIO_Mode_IPU;
    GPIO_InitStructure0.GPIO_Pin   = GPIO_Pin_0;
    GPIO_InitStructure0.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure0);
	
    //Beep(DO, 400);  Beep(RE, 400);  Beep(MI, 400);  Beep(FA, 400);
    //Beep(SOL, 400); Beep(LA, 400);  Beep(SI, 400);

		//uint16_t tune[]  = {DO, DO, SOL, SOL, LA, LA, SOL,   FA, FA, MI, MI, RE, RE, DO};
		//uint16_t beat[]  = {400,400,400,400,400,400,800,   400,400,400,400,400,400,800};
		//for (int i = 0; i < 14; i++){
		//	Beep(tune[i], beat[i]);
		//	Delay_us(100);
		//}
		
    while (1) {
			uint8_t key = GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0); 
			GPIO_WriteBit(GPIOA,GPIO_Pin_4,(BitAction)key);

		}
}

 

 

 

点灯PC13

#include "stm32f10x.h"

void Delay_ms(uint32_t ms)

{

uint32_t i, j;

for (i = 0; i < ms; i++)

for (j = 0; j < 7200; j++);

}

int main(void)

{

RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);

GPIO_InitTypeDef GPIO_InitStructure;

GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_Out_PP;

GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_13;

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_Init(GPIOC, &GPIO_InitStructure);

GPIO_ResetBits(GPIOC,GPIO_Pin_13);

while (1)

{

}

}

闪灯PC13

#include "stm32f10x.h"

void Delay_ms(uint32_t ms)

{

uint32_t i, j;

for (i = 0; i < ms; i++)

for (j = 0; j < 7200; j++);

}

int main(void)

{

RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);

GPIO_InitTypeDef GPIO_InitStructure;

GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_Out_PP;

GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_13;

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_Init(GPIOC, &GPIO_InitStructure);

GPIO_ResetBits(GPIOC,GPIO_Pin_13);

while (1)

{

GPIO_SetBits(GPIOC,GPIO_Pin_13);

Delay_ms(120);

GPIO_ResetBits(GPIOC,GPIO_Pin_13);

Delay_ms(120);

}

}

流水灯

#include "stm32f10x.h"

void Delay_ms(uint32_t ms)
{
    uint32_t i, j;
    for (i = 0; i < ms; i++)
        for (j = 0; j < 7200; j++);
}

int main(void)
{
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
    GPIO_InitTypeDef GPIO_InitStructure1;
    GPIO_InitStructure1.GPIO_Mode  = GPIO_Mode_Out_PP;
    GPIO_InitStructure1.GPIO_Pin   = GPIO_Pin_0;
    GPIO_InitStructure1.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure1);
		
	  GPIO_InitTypeDef GPIO_InitStructure2;
    GPIO_InitStructure2.GPIO_Mode  = GPIO_Mode_Out_PP;
    GPIO_InitStructure2.GPIO_Pin   = GPIO_Pin_1;
    GPIO_InitStructure2.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure2);
	  
	  GPIO_InitTypeDef GPIO_InitStructure3;
    GPIO_InitStructure3.GPIO_Mode  = GPIO_Mode_Out_PP;
    GPIO_InitStructure3.GPIO_Pin   = GPIO_Pin_2;
    GPIO_InitStructure3.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure3);
	
    while (1)
    {
        GPIO_SetBits(GPIOA,GPIO_Pin_0);
				Delay_ms(120);
				GPIO_ResetBits(GPIOA,GPIO_Pin_0);
				Delay_ms(120);
			GPIO_SetBits(GPIOA,GPIO_Pin_1);
				Delay_ms(120);
				GPIO_ResetBits(GPIOA,GPIO_Pin_1);
				Delay_ms(120);
			GPIO_SetBits(GPIOA,GPIO_Pin_2);
				Delay_ms(120);
				GPIO_ResetBits(GPIOA,GPIO_Pin_2);
				Delay_ms(120);
    }
}

蜂鸣器唱小星星:

#include "stm32f10x.h"

#define DO  262
#define RE  294
#define MI  330
#define FA  349
#define SOL 392
#define LA  440
#define SI  494

void Delay_us(uint32_t us)
{
    uint32_t i, j;
    for (i = 0; i < us; i++)
        for (j = 0; j < 7; j++);
}


void Beep(uint16_t freq, uint16_t ms)
{
    uint32_t half_us = 500000 / freq;      
    uint32_t cycles  = (uint32_t)freq * ms / 1000;  
    for (uint32_t i = 0; i < cycles; i++)
    {
        GPIO_SetBits(GPIOA, GPIO_Pin_0);
        Delay_us(half_us);
        GPIO_ResetBits(GPIOA, GPIO_Pin_0);
        Delay_us(half_us);
    }
}

int main(void)
{
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
    GPIO_InitTypeDef GPIO_InitStructure;
    GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_Out_PP;
    GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_0;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

   
    Beep(DO, 400);  Beep(RE, 400);  Beep(MI, 400);  Beep(FA, 400);
    Beep(SOL, 400); Beep(LA, 400);  Beep(SI, 400);

		uint16_t tune[]  = {DO, DO, SOL, SOL, LA, LA, SOL,   FA, FA, MI, MI, RE, RE, DO};
		uint16_t beat[]  = {400,400,400,400,400,400,800,   400,400,400,400,400,400,800};
		for (int i = 0; i < 14; i++){
			Beep(tune[i], beat[i]);
			Delay_us(100);
		}
		
    while (1) { }
}

 

posted on 2026-10-19 16:43  fafrkvit  阅读(7)  评论(0)    收藏  举报