CentOS7 下 keepalived 的安装和配置

安装前准备：
yum -y install gcc gcc-c++ autoconf automake make 
yum -y install zlib zlib-devel openssl openssl-devel pcre pcre-devel

一、下载keepalived
方法一：
yum -y install keepalived
方法二：
下载二进制源码包：http://www.keepalived.org/download.html
#下载安装文件

cd /usr/local/src
wget http://www.keepalived.org/software/keepalived-1.4.0.tar.gz 
#解压文件
tar -zxvf keepalived-1.40.0.tar.gz
#编译
cd keepalived-1.40.0/
#--prefix 指定安装地址
#/usr/local/keepalived/ 安装的目录，不要和自己安装文件一个目录，不然报错
./configure --prefix=/usr/local/keepalived/
#编译并安装
 make && make install

　　

配置：（后面部分会详细介绍，这里就用默认配置）

 

启动：

首先拷贝几个文件到CentOS7环境中：

[root@localhost ~]# cp keepalived-1.3.4/keepalived/etc/init.d/keepalived /etc/init.d/
[root@localhost ~]# mkdir /etc/keepalived
[root@localhost ~]# cp /usr/local/keepalived/etc/keepalived/keepalived.conf /etc/keepalived/
[root@localhost ~]# cp keepalived-1.3.4/keepalived/etc/sysconfig/keepalived /etc/sysconfig/
[root@localhost ~]# cp /usr/local/keepalived/sbin/keepalived /usr/sbin/

　　

二、编辑/etc/keepalived/keepalived.conf

yum安装编辑此文件
    vim /ect/keepalived/keepalived.conf
源码包安装编辑此文件

 vim /usr/local/keepalived/etc/keepalived/keepalived.conf 
global_defs {
    notification_email {
        #mr@mruse.cn       # 指定keepalived在发生切换时需要发送email到的对象，一行一个
        #sysadmin@firewall.loc
    }
    notification_email_from xxx@163.com   # 指定发件人
    smtp_server smtp@163.com              # smtp 服务器地址
    smtp_connect_timeout 30               # smtp 服务器连接超时时间
    router_id LVS_1 # 标识本节点的字符串,通常为hostname,但不一定非得是hostname,故障发生时,邮件通知会用到
    }

vrrp_instance VI_1 {  # 实例名称
    state MASTER      # 可以是MASTER或BACKUP，不过当其他节点keepalived启动时会将priority比较大的节点选举为MASTER
    interface eth0    # 节点固有IP（非VIP）的网卡，用来发VRRP包做心跳检测
    mcast_src_ip 192.168.0.179 #本机的ip，需要修改
    virtual_router_id 51 # 虚拟路由ID,取值在0-255之间,用来区分多个instance的VRRP组播,同一网段内ID不能重复;主备必须为一样;
    priority 100      # 用来选举master的,要成为master那么这个选项的值最好高于其他机器50个点,该项取值范围是1-255(在此范围之外会被识别成默认值100)
    advert_int 1      # 检查间隔默认为1秒,即1秒进行一次master选举(可以认为是健康查检时间间隔)
    authentication {  # 认证区域,认证类型有PASS和HA（IPSEC）,推荐使用PASS(密码只识别前8位)
        auth_type PASS  # 默认是PASS认证
        auth_pass MrUse # PASS认证密码
    }
    virtual_ipaddress {
        192.168.0.219    # 虚拟VIP地址,允许多个
    }
}

　　

三、开启服务
（1）systemctl start keepalived（在yum安装时直接使用此命令启动服务）
（2）源码包安装启动服务还需进行如下步骤
#创建keepalived配置文件目录
mkdir /etc/keepalived

 #拷贝配置文件到/etc/keepalived目录下
    cp /usr/local/keepalived/etc/keepalived/keepalived.conf /etc/keepalived/

    #复制keepalived脚本到/etc/init.d/ 目录
    cp /usr/local/keepalived/etc/rc.d/init.d/keepalived /etc/init.d/ #(可忽略) 
    #拷贝keepalived脚本到/etc/sysconfig/ 目录
    cp /usr/local/keepalived/etc/sysconfig/keepalived /etc/sysconfig/

    #建立软连接
    ln -s /usr/local/keepalived/sbin/keepalived /sbin/

    #添加到开机启动
    chkconfig keepalived on
    #查看服务状况
    systemctl status keepalived

　　

四、启用ip转发

echo "net.ipv4.ip_forward = 1" >> /etc/sysctl.conf
    sysctl -p

五、防火墙添加规则

　　firewall-cmd --direct --permanent --add-rule ipv4 filter INPUT 0 --in-interface enp196 --destination 224.0.0.18 --protocol vrrp -j ACCEPT

success
# firewall-cmd --direct --permanent --add-rule ipv4 filter OUTPUT 0 \--out-interface enp196 --destination 224.0.0.18 --protocol vrrp -j ACCEPT
success
# firewall-cmd --reload
success