管理口信息：
192.168.2.100
Administrator/Admin@9000
磁盘阵列配置：https://blog.csdn.net/m0_48515896/article/details/140158217
1.4个内存有告警
2.没有raid卡
3.vmware检测不到本地存储
在安装的时候必须在管理口添加一下存储硬盘
在esxi交换机创建网络
参考文档：https://www.cnblogs.com/mojt/p/17340472.html
https://blog.csdn.net/m0_58320241/article/details/141424817
克隆一个虚机的参考文档：https://blog.csdn.net/m0_54434140/article/details/132713024
find / -name DLS1A
cd /vmfs/volumes/673da27d-7b4f3f88-3daf-347379394162/DLS1A
mkdir ../DLS1B
cp DLS1A.vmx ../DLS1B/DLS1B.vmx
vmkfstools -i ../DLS1A/DLS1A.vmdk ../DLS1B/DLS1B.vmdk
cd ..
ls
cd DLS1B/
ls
ll
vi DLS1B.vmx
vim DLS1B.vmx
++++++++++++++++++++++++++++++++++++++++++
克隆一个虚机的参考文档：https://blog.csdn.net/m0_54434140/article/details/132713024
1.创建目录
mkdir /vmfs/volumes/673da27d-7b4f3f88-3daf-347379394162/DLS
2.复制文件
cd /vmfs/volumes/673da27d-7b4f3f88-3daf-347379394162/
cp ./DLS1A/DLS1A.vmx ./DLS/DLS.vmx
3.克隆vmdk文件
vmkfstools -i ./DLS1A/DLS1A.vmdk ./DLS/DLS.vmdk
4.替换虚机名称
sed -i 's/DLS1A/DLS/' ./DLS/DLS.vmx
划分交换机的vlan
恢复出厂值：restore factory-default
1.配置vlan步骤：
1.console
2.system-view
3.vlan 10 11 13 14 15
15 SW1-1
10 SW1-2
11 SW1-3
13 SW1-4
10 SW1-5
14 SW1-6
14 SW1-7
2.查看接口
[H3C-vlan10]display vlan brief
Brief information about all VLANs:
Supported Minimum VLAN ID: 1
Supported Maximum VLAN ID: 4094
Default VLAN ID: 1
VLAN ID Name Port
1 VLAN 0001 GE1/0/1 GE1/0/2 GE1/0/3 GE1/0/4
GE1/0/5 GE1/0/6 GE1/0/7 GE1/0/8
GE1/0/9 GE1/0/10 GE1/0/11
GE1/0/12 GE1/0/13 GE1/0/14
GE1/0/15 GE1/0/16 GE1/0/17
GE1/0/18 GE1/0/19 GE1/0/20
GE1/0/21 GE1/0/22 GE1/0/23
GE1/0/24 GE1/0/25 GE1/0/26
GE1/0/27 GE1/0/28
10 VLAN 0010
11 VLAN 0011
13 VLAN 0013
14 VLAN 0014
15 VLAN 0015
3.将接口添加到vlan
[H3C] interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/1] port link-type access
[H3C-GigabitEthernet1/0/1] port access（这个地方和华为不一样） vlan 15 华为命令：port default vlan 15
[H3C-GigabitEthernet1/0/1] quit
[H3C]
4.显示vlan信息
display vlan brief
5.保存配置save
6.配置网关
system-view
interface Vlan-interface 10
ip address 10.199.200.1 255.255.255.248
quit
interface Vlan-interface 11
ip address 10.199.200.9 255.255.255.248
interface Vlan-interface 13
ip address 10.199.200.25 255.255.255.248
interface Vlan-interface 14
ip address 10.199.200.65 255.255.255.192
interface Vlan-interface 15
ip address 10.199.200.129 255.255.255.128
7.显示vlan 的ip信息
[H3C]display interface Vlan-interface brief
Brief information on interfaces in route mode:
Link: ADM - administratively down; Stby - standby
Protocol: (s) - spoofing
Interface Link Protocol Primary IP Description
Vlan1 DOWN DOWN 192.168.0.233
Vlan10 DOWN DOWN 10.199.200.1
Vlan11 DOWN DOWN 10.199.200.9
Vlan13 DOWN DOWN 10.199.200.25
Vlan14 DOWN DOWN 10.198.200.65
Vlan15 DOWN DOWN 10.199.200.129
上述的端口是down状态，需要插入物理网口以后会自动启动为up状态
10 SW1-2
10 SW1-5
11 SW1-3
13 SW1-4
14 SW1-6
14 SW1-7
15 SW1-1
vmNIC7(PORT 7) SW1-1
vmNIC0(PORT 0)（port10） SW1-2
vmNIC1(PORT 1)（port11） SW1-3
vmNIC3(PORT 3) SW1-4
vmNIC2(PORT 2) SW1-5
vmNIC4(PORT 4) SW1-6
vmNIC5(PORT 5) SW1-7
8.增加cmp的vlan到交换机1上（华三）
15 SW3-1(11)
14 SW3-2(12)
14 SW3-3(13)
SW3-4(14)
14 SW3-5(15)
SW3-6(16)
14
14
81 SW3-7(17)
SW4-1（21）要删除
SW4-2（22）要删除
[H3C] interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/1] port link-type access
[H3C-GigabitEthernet1/0/1] port access vlan 15
[H3C-GigabitEthernet1/0/1] quit
9.开启交换机ssh登录
https://blog.csdn.net/i12344/article/details/138706431
1>开启ssh
ssh server enable //开启SSH
public-key local create rsa //创建rsa密钥
public-key local create dsa //创建dsa密钥
2>配置VTY虚拟接口
user-interface vty 4 //进入vty配置
authentication-mode scheme //设置认证模式
protocol inbound ssh //设置登陆协议为ssh
quit //退出VTY
3>创建本地用户
local-user administator //创建了一个helen的用户
password simple T@R63dis //密码是helen123
service-type ssh //设置用户登陆权限为ssh
4>赋予权限
local-user administrator
authorization-attribute user-role level-15
authorization-attribute user-role network-admin
authorization-attribute user-role network-operator
save
10.删除81vlan的21和22端口
undo port GigabitEthernet 1/0/22
undo port GigabitEthernet 1/0/21
华为5700配置
https://support.huawei.com/enterprise/zh/doc/EDOC1100088143/
11.清除密码
1、Console插到交换机
2、加电重启 按住ctrl+b
3、输入密码Admin@huawei.com
4、按7选项
5、在按1选项；自动重启
6、重新设置密码即可
用默认模式启动交换机
12.恢复出厂配置
13.显示接口信息
display interfaces brief
vlan 20
interface GigabitEthernet 0/0/1
20 SW2-2
20 SW2-5
21 SW2-3
23 SW2-4
24 SW2-6
24 SW2-7
25 SW2-1
interface GigabitEthernet 0/0/7
port link-type access
port default vlan 24
interface vlanif 20
ip address 10.198.200.1 255.255.255.248
interface vlanif 25
ip address 10.198.200.129 255.255.255.128
查看
display ip interface brief
14.
c3
eth0 00:0c:29:45:03:10 mgmt
eth3 00:0c:29:45:03:06 cluster
db
eth0: 00:0c:29:e7:36:a3 mgmt
eth3: 00:0c:29:e7:36:99 cluster
15. 根据名字进行匹配的
北风之神:
c3--199---->osv1.iso----->primary<----->node1的地址
db---198--->osv2.iso----->secondary<---->node2的地址
北风之神:
以后做数据可以倒过来，就对了
16.suse linux在osv系统开启root远程登录
1>vi /etc/ssh/sshd_config
注释掉一下
#PermitRootLogin without-password
下面的改为yes
PermitRootLogin yes
2>cat /etc/security/access.conf
把开头是-改为+
3>重启服务
service sshd restart
18.华为和华三交换机
设置接口类型命令不一样
华三：port access vlan 15
华为：port default vlan 15
退出命令不一样：
华为：q，quit
华三：quit
查看vlan概述：
华三：dis vlan brif
华为：dis vlan
19.配置cmp
1>配置osv交换机(这个步骤大概需要耗时7分钟左右)
配置------》常规（房屋的图标）-----》交换机
10.199.200.2 SRX/2GwN!gb4 复制ip地址的时候ip不要带空格，否则报错
2>创建局号和号段资源
61 号段0000-9999
3>BG配置(这一步需要先保存，然后在编辑打开，把相关参数修改和文档一样)
配置------》业务组（第三个图标）-----》业务组列表-----》添加
4>创建服务类别
用于限制分机的呼叫权限如（国际、国内、本地、内线）
也就是市话权限
配置-----》openscapevoice-----》全局转换与路由（第四个图标）------》转换-----》限制类型-----》添加
5>创建拨号方案
6>终端配置文件
20.删除三层接口：undo interface Vlanif81
21.Mediaserver文档有错误
MediaServer镜像包安装（注意下面是连接mediaserver服务器不是cmp服务器）
22.suse修改主机名
MediaServer:~ # sysctl -w kernel.hostname=mediaserverc3
kernel.hostname = MediaServerDB
MediaServer:~ # cat /proc/sys/kernel/hostname
MediaServerDB
MediaServer:~ #
修改 /etc/hostname
23.安装Mediaserver
mkdir -p /software/uc/
mount -o loop /software/uc/OpenScapeUcSuiteApps-Repository-V10R5.0.0-020000.iso /mnt
cp /mnt/templates/knut.responsefile.txt.templ_MediaServerStandalone /root/knut.responsefile.txt;
cp /mnt/support/checkResponsefileOnLocalNode.sh /root;
vi /root/knut.responsefile.txt;
chmod +w /root/knut.responsefile.txt;
chmod +x /root/checkResponsefileOnLocalNode.sh;
cd ~
./checkResponsefileOnLocalNode.sh knut.responsefile.txt
umount /mnt;
zypper ar iso:/?iso=/software/uc/OpenScapeUcSuiteApps-Repository-V10R5.0.0-020000.iso ucapp
zypper lr;
zypper ref; 刷新本地库 看到提示后a回车
zypper in osc-setup
zypper rr 删除一个库
mkdir –p /software/repo; 这个目录必须是空，否则无法安装
cd /software/uc;
osc-setup cr -e /software/repo OpenScapeUcSuiteApps-BasePackage-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-Chinese-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-English-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-OptionalPackage-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-Repository-V10R5.0.0-020000.iso
现网只有四个镜像：osc-setup cr -e /software/repo OpenScapeUcSuiteApps-BasePackage-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-Chinese-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-English-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-Repository-V10R5.0.0-020000.iso
osc-setup lr
osc-setup ref
osc-setup in OpenScapeUC_MediaServerStandalone
osc-setup cr --clean
osc-setup in mediaserver_announcements_zh
osc-setup in mediaserver_autoattendant_languagepack_ZH-CN
osc-setup in mediaserver_voiceportal_languagepack_ZH-CN 安装不成功
osc-setup in scs_conferencing_languagepack_zh_cn
osc-setup in uc-asr-zh_cn
错误：
mediaserverc3:/software/uc # osc-setup cr -e /software/repo OpenScapeUcSuiteApps-BasePackage-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-Chinese-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-English-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-OptionalPackage-V10R5.0.0-020000.iso OpenScapeUcSuiteApps-Repository-V10R5.0.0-020000.iso
If 'osc-setup' is not a typo you can use command-not-found to lookup the package that contains it, like this:
cnf osc-setup
解决方法：
1.可以通过yast安装osc-setup软件解决
错误二：
mediaserverc3:/home # osc-setup in mediaserver_voiceportal_languagepack_ZH-CN
Logging to: /var/log/OpenScapeUC/osc-setup-2024-12-04_23-14-07.log
osc-setup version: "9.3.0-88"
SUSE VERSION: 12 SERVICEPACK: 12
Refreshing repository data...
Verbosity: 1
Initializing Target
Specified repositories:
Checking whether to refresh metadata for CREATED_REPO
Repository 'CREATED_REPO' is up to date.
All repositories have been refreshed.
Refresh end
Logging to: /var/log/OpenScapeUC/checkdep-2024-12-04_23-12-08.log
checking dependencies for "mediaserver_voiceportal_languagepack_ZH-CN"
Logfile: /var/log/OpenScapeUC/checkdep-2024-12-04_23-12-08.log
checking.... mediaserver_voiceportal_languagepack_ZH-CN
Installing optional package "mediaserver_voiceportal_languagepack_ZH-CN"
starting test (this could take some minutes....)
Test failed. If you got a download error please recreate the repository with additional ISOs.
Error was:
Loading repository data...
Reading installed packages...
Resolving package dependencies...
Problem: mediaserver_voiceportal_languagepack_ZH-CN-9.4_0.0.0-0.i586 requires mediaserver_voiceportal, but this requirement cannot be provided
uninstallable providers: mediaserver_voiceportal-9.4_0.47.0-10.noarch[CREATED_REPO]
Solution 1: deinstallation of OpenScapeUC_MediaServerStandalone-10.4.0-2.noarch
Solution 2: do not install mediaserver_voiceportal_languagepack_ZH-CN-9.4_0.0.0-0.i586
Solution 3: break mediaserver_voiceportal_languagepack_ZH-CN-9.4_0.0.0-0.i586 by ignoring some of its dependencies
Choose from above solutions by number or cancel [1/2/3/c] (c): c
Test failed. If you got a download error please recreate the repository with additional ISOs.
Operation took: 2 seconds
Logfile: /var/log/OpenScapeUC/osc-setup-2024-12-04_23-14-07.log
这个是因为系统已经安装的版本比将要安装的版本高，应该不用再安装了
已经安装的版本：OpenScapeUC_MediaServerStandalone-10.4.0-2.noarch ，这个可以通过rpm -e卸载，然后就可以osc-setup in mediaserver_voiceportal_languagepack_ZH-CN
将要安装的版本：9.3.0-88
可以全部卸载：zypper remove OpenScapeUC_frida_MediaServerStandalone-10.4.0-2.noarch，用zypper命令进行卸载
下面是现网环境的安装包
total 8097228
-rw-r--r-- 1 root root 3734138880 Aug 11 2023 OpenScapeUcSuiteApps-BasePackage-V10R5.0.0-020000.iso
-rw-r--r-- 1 root root 1209489408 Aug 11 2023 OpenScapeUcSuiteApps-Chinese-V10R5.0.0-020000.iso
-rw-r--r-- 1 root root 3238733824 Aug 11 2023 OpenScapeUcSuiteApps-English-V10R5.0.0-020000.iso
-rw-r--r-- 1 root root 109195264 Aug 11 2023 OpenScapeUcSuiteApps-Repository-V10R5.0.0-020000.iso
24.dns安装以后反向不能解析
C:\Users\YYP>nslookup c3.shmetro.com
Server: UnKnown 出现这个可以参考这个来解决：https://blog.csdn.net/weixin_34319111/article/details/91549796
Address: 10.199.200.72
Name: c3.shmetro.com
Address: 10.199.200.10
同时可以在hosts增加
10.199.200.72 dns-c3.shmetro.com
10.198.200.72 dns-db.shmetro.com
下面是正确的解析：
C:\Users\YYP>nslookup c3.shmetro.com
Server: dns-c3.shmetro.com
Address: 10.199.200.72
Name: c3.shmetro.com
Address: 10.199.200.10
C:\Users\YYP>nslookup -type=srv _sip._udp.reg.shmetro.com
Server: dns-c3.shmetro.com
Address: 10.199.200.72
_sip._udp.reg.shmetro.com SRV service location:
priority = 10
weight = 0
port = 5060
svr hostname = c3.shmetro.com
_sip._udp.reg.shmetro.com SRV service location:
priority = 10
weight = 0
port = 5060
svr hostname = db.shmetro.com
c3.shmetro.com internet address = 10.199.200.10
db.shmetro.com internet address = 10.198.200.10
C:\Users\YYP>
注意：dns安装文档最后一步的测试命令和现场不一样
1》
nslookup -type=srv _sip._udp.regc3.shmetro.com这个多个c3
nslookup -type=srv _sip._udp.reg.shmetro.com这个是正确的
2》
srv不用这个命令nslookup reg.shmetro.com
nslookup -type=srv _sip._udp.regosbline1.shmetro.com
25.sbc安装完成以后操作系统root/T@R63dis ,这个是默认密码
SBC的地址 https://xxx.xxx.xxx.xxx 登录SBC，输入用户名administrator密码Asd123!.
26.安装sql server 数据库
hosts
DLS 10.199.200.70
DLS1A 10.199.200.68
DLS1B 10.199.200.69
28.修改dns服务器的时钟服务器
设置时间服务器
w32tm /config /syncfromflags:manual /manualpeerlist:"10.199.200.66"
同步时间服务器
w32tm /config /manualpeerlist:"10.199.200.66" /syncfromflags:manual /reliable:yes /update
停止时间服务
net stop w32time
启动时间服务
net start w32time
检查同步状态
w32tm /query /status
29.osb安装的时候，制作数据的时候，虚拟硬件选择6000的那个类型
如果安装完成以后出现这个错误：error: cannot mount partition/disk 'active', it was not found.
需要去--->>https://10.101.81.5/login.html----->>Maintenance--->install/upgrade------->>install
语音包安装,需要上传语音包
30.做话机的DHCP以及dns和dls地址下发
vlan 80
10.101.2.0/24 10.101.2.1
dns
GE0/0/12(D) GE0/0/13(D) GE0/0/14(D) GE0/0/15(D)
GE0/0/16(U) GE0/0/17(D) GE0/0/18(D) GE0/0/19(D)
GE0/0/20(D) GE0/0/21(D) GE0/0/22(D)
interface GigabitEthernet 0/0/12
port link-type access
port default vlan 80
quit
interface GigabitEthernet 0/0/13
port link-type access
port default vlan 80
quit
interface GigabitEthernet 0/0/14
port link-type access
port default vlan 80
quit
interface GigabitEthernet 0/0/15
port link-type access
port default vlan 80
quit
interface GigabitEthernet 0/0/16
port link-type access
port default vlan 80
quit
interface GigabitEthernet 0/0/17
port link-type access
port default vlan 80
quit
interface GigabitEthernet 0/0/18
port link-type access
port default vlan 80
quit
interface GigabitEthernet 0/0/19
port link-type access
port default vlan 80
quit
interface GigabitEthernet 0/0/20
port link-type access
port default vlan 80
quit
interface GigabitEthernet 0/0/21
port link-type access
port default vlan 80
quit
interface GigabitEthernet 0/0/22
port link-type access
port default vlan 80
quit
dhcp配置 以下是全局配置dhcp
dhcp enable
network 10.101.2.0 mask 24
gateway-list 10.101.2.1
dns-list 10.199.200.72
dns-list 10.198.200.72
excluded-ip-address 10.101.2.1
lease day 3
dhcp server option 43 ascii 01075369656d656e73031A73646C703A2F2F31302E31302E33302E3234343A3138343433 下发dls数据
需要在哪个port开启这个服务 以下是全局配置dhcp
nterface Vlan 80
dhcp selece global
覃斌给的是在接口上配置dhcp
interface Vlanif80
ip address 10.101.2.1 255.255.255.0
dhcp select interface
dhcp server excluded-ip-address 10.10.29.1 10.10.29.245
dhcp server lease day 100 hour 23 minute 0
dhcp server dns-list 10.199.200.72
dhcp server dns-list 10.198.200.72
dhcp server option 43 ascii 01075369656d656e73031A73646C703A2F2F31302E31302E33302E3234343A3138343433 （Siemenssdlp://10.10.30.244:18443 https://www.convertstore.com/number/asciitohex/zh%2fascii-text-to-hex-converter.html）
dhcp server option 43 ascii 01 07 53 69 65 6d 65 6e 73 03 1a 73 64 6c 70 3a 2f 2f 31 30 2e 31 39 39 2e 32 30 30 2e 36 37 3a 31 38 34 34 33
修改arp老化周期
arp expire-time 60（华为，单位为秒）
arp timer aging 1（华三，单位为分钟）
https://www.convertstore.com/number/hextoascii/zh/%E2%80%9C/home/privacy%E2%80%9D#google_vignette
31.osv数据配置
32.nlb配置
1.打开nlb配置界面
2.通过通过业务地址（10.199.200.68，不是心跳地址192.168.2.10）进行添加集群，选择业务地址10.199.200.67
3.配置集群地址10.199.200.67
4.配置端口
删除原来的0-65535端口
新增10443-10444端口
新增18080-18080端口
新增18443-18444端口
5.在另外一台机器上重复操作以上步骤
nlb stop
netstat interface show interface
netsh interface set interface cluster admin=disable
33. 610000
AAbb1122
34.如果ip话机出现unobtainable状态
登录话机-----》system------》System identity------》enable id的勾打上
35.ip话机不用模版，通过ip地址注册，
ip地址发请求------》osb---------------》osv1
10.101.2.253 10.101.81.5 10.199.200.10
话机 osb转发 osv注册服务器
36.srv不用这个命令nslookup reg.shmetro.com
37.今天的模版不能下发和cmp上sip的配置可能有关系
可能是由于38条的dns没有创建影响
38.dns配置缺少下面配置，在文档的11页，需要手动添加
regosbline1.shmetro.com
39.时间服务器时区相差8小时，是因为使用的utc时间
cmp-----》linux命令---》yast----》system----》date&time----》去掉 Hardware Clock Set to UTC的勾
40.如果在配置ntpserver的时候报错如下，
ntp报错
Error │
Cannot write settings to '/etc/ntp.con
那么等几十分钟会自己好的。
cmp:/etc # cat /etc/ntp.conf |grep -v '^#'
server 127.127.1.0 # local clock (LCL)
fudge 127.127.1.0 stratum 10 # LCL is unsynchronized
restrict -4 default notrap nomodify nopeer noquery
restrict -6 default notrap nomodify nopeer noquery
restrict 127.0.0.1
restrict ::1
driftfile /var/lib/ntp/drift/ntp.drift # path for drift file
logfile /var/log/ntp # alternate log file
keys /etc/ntp.keys # path for keys file
trustedkey 1 # define trusted keys
requestkey 1 # key (7) for accessing server variables
controlkey 1 # key (6) for accessing server variables
10.199.200.66 iburst
41.话机时间和实际时间相差8小时（模版下发的timezoneoffset是0）
42.模版创建过程
1.location创建
Administrator----》Server Configuration---》location
2.
43.删除注册记录（默认是30天）
Administrator-----》serverConfiguration---》p&psettings
44.创建模版
45.如果有模版在使用，如果创建新的模版会导致在用模版失效
47.拨号后呼叫延时150秒左右
610000注册在sbc 用模版line1-record
6100001注册在osb，用模版line1-norecord
有问题呼叫
610001------》610000延时150秒左右
解决办法：大概是osbline1的媒体包没有安装
无问题呼叫
610000----》610001正常
48.610002采用模块line1-norecord 注册没有授权
在osbline1抓包看到没有授权，然后检查话机参数发现采用的是tcp连接，应该选用udp连接
49.华三交换机下载日志（参考文档860页）
1》保存log文件
logfile save
2》开启ftp server
ftp server enable
2》给账号增加ftp权限（进入账号进行操作）
service-type ftp
3》windows的cmd操作下载
C:\Users\YYP>ftp 10.199.200.129
Connected to 10.199.200.129.
220 FTP service ready.
502 Command not implemented.
User (10.199.200.129:(none)): administrator
331 Password required for administrator.
Password:
230 User logged in.
ftp> get /logfile/logfile.log
200 PORT command successful
150-Connecting to port 12587
150 7943.1 kbytes to download
226 File successfully transferred
ftp: 8196254 bytes received in 7.05Seconds 1163.08Kbytes/sec.
ftp>
华三交换机开通ftp sever功能
ftp server enable
local-user administrator
service-type ftp
dis this
#
local-user administrator class manage
password hash $h$6$sTEtn9B246iCSdJt$vOP3kKQhJ4NvPhCZMu4SZAufDqOaLlNBy+cRbNnnK5Jih21TJPibqHgvB0YXm7KakFv7sLu4q+T1y/AWQ6iIsw==
service-type ftp
service-type ssh
authorization-attribute user-role level-15
authorization-attribute user-role network-admin
authorization-attribute user-role network-operator
#
return
华为交换机配置ftp server功能：参考https://www.cnblogs.com/flash100/p/12410771.html
sys
ftp server enable
aaa
local-user ftp password cipher T@R63dis
local-user ftp privilege level 15
local-user ftp service-type ftp
local-user ftp ftp-directory flash:/ #这里是交换机当前目录
quit
save
设置已有admin账号的ftp权限
local-user admin service-type ftp
local-user admin ftp-directory flash:/
C:\Users\YYP>ftp 10.199.200.129
Connected to 10.199.200.129.
220 FTP service ready.
502 Command not implemented.
User (10.199.200.129:(none)): administrator
331 Password required for administrator.
Password:
230 User logged in.
ftp> get /logfile/logfile.log
200 PORT command successful
150-Connecting to port 12587
150 7943.1 kbytes to download
226 File successfully transferred
ftp: 8196254 bytes received in 7.05Seconds 1163.08Kbytes/sec.
ftp>
华为交换机配置ftp服务器：
1》ftp server enable
2》给账号赋予ftp权限
50. 抓包
tethereal -i any -w /tmp/test.cap
51.华为交换机修改密码
aaa
local-user admin password cipher T@R63dis
52.开启华三交换机远程登录
https://blog.csdn.net/zjk2581101228/article/details/137625596
53.华为交换机开启远程登录
https://blog.csdn.net/i12344/article/details/138706431
54.
浙公网安备 33010602011771号