UHP Command List
UHP Command List
# #N,Name,Sat_long,polariz,profile,rx_freq,sym_rate #N: Key identifier #Name: Network name #Sat_long: Satellite longitude in format XXXYYZ # where XXX degrees, YY minutes, Z – W/E #polariz: 1-vertical/left, 2-horizontal/right #profile: 1-8 number of configuration profile to be activated; # When this parameter is set to 0 the default central frequency and symbol rate of the profile # will be ignored in favor of the following customized values #rx_freq: Customized central frequency #sym_rate: Customized central frequency # N,ASIA7,10530E,2,0,12718000,15800 # #A,lat,lon,dia,eirp #A: Key identifier #lat: Beam center latitude in format XXXYYZ #log: Beam center longitude in format XXXYYZ #dia: Beam diameter in degrees (10) or in miles (10m) or in kilometers (10k) #eirp: EIRP value in range of 0-100 # A,2936N,12045E,300k,53 # #Exammple #(ASIA7,H,12718000,10600,15800) #(CHINASAT12,V,12386000,10600,4270) #(29.6N,120.75E)=(2936N,12045E) #(25.2N,114.8E)=(2512N,11448E) # N,ASIA7,10530E,2,0,12718000,15800 A,2936N,12045E,300k,53 N,CHINASAT12,8730E,1,0,12386000,4270 A,2512N,11448E,300k,50
# #Beam switching #(ASIA7 105.5E 40000Ksps 12717MHz 10600MHz 12800MHz V) # #N,Name,Sat_long,polariz,profile,rx_freq,sym_rate #N: Key identifier #Name: Network name #Sat_long: Satellite longitude in format XXXYYZ # where XXX degrees, YY minutes, Z – W/E #polariz: 1-vertical/left, 2-horizontal/right #profile: 1-8 number of configuration profile to be activated; # When this parameter is set to 0 the default central frequency and symbol rate of the profile # will be ignored in favor of the following customized values #rx_freq: Customized central frequency #sym_rate: Customized central frequency # #hunt_freq: Hunt frequency in MHz #hunt_bw: Hunt bandwidth in MHz #rx_LO: Receiving local oscillator frequency #tx_LO: Transmitting local oscillator frequency # N,A7_50,10530,1,0,2117000,40000, 2117000,40000.000,10600000,12800000 P,4,3944,12519,3857,12722,3708,12835,3456,12845,3246,12819,3041,12733,2841,12636,2639,12543,2436,12453,2238,12352,2103,12219,2006,12020,1930,11812,1828,11615,1703,11432,1513,11318,1350,11421,1418,11632,1509,11834,1543,12044,1405,12132,1217,12011,1044,11836,920,11653,803,11505,706,11305,724,11056,750,10847,737,10635,714,10424,701,10211,652,9959,635,9747,634,9534,730,9335,918,9220,1123,9133,1331,9058,1542,9034,1753,9044,1948,9146,2045,9344,1959,9543,1808,9656,1623,9816,1600,10018,1722,10201,1901,10330,2032,10507,2204,10643,2341,10814,2530,10930,2730,11022,2942,11010,3151,11004,3333,11123,3507,11300,3625,11446,3721,11646,3818,11846,3904,12051,3938,12300,3946,12512
# ACU <--> Modem --> a 2 <-- A 5 # <-- S 105.500 0 0 <-- P H V <-- H 1786.0 15.800 <-- B 10600.0 12800.0 <-- F # $GCCMD,OPENAMIP SET,S 105.500000 0.000000 0.000000,H 1786.000000 15800.000000,P H V,B 10600.000000 12800.000000,X 2 20000 15000 0 2 9750 9750 10600 10600 0,T ,A ,W ,L ,K ,F*40 # <-- L 0 0 <-- W 600 --> s 1 0 --> w 1 29.600 120.750 1638946429 42.700 267.400 0.000 0.510 -0.410 0 # <-- L 1 1 <-- W 600 --> s 1 1 --> w 1 29.600 120.750 1638946538 42.700 267.400 0.000 0.510 -0.410 0 #
COTM: LocationSource(Network) TxControl(Local) AMIP: PeerIP(192.168.222.5) Port(4001) VLAN(0) 发射功率: Tx(-27dBm) Max(-22dBm) TDMA时序模式: Location 入网超时时间: Timeout(120s) 漫游超时时间: Roaming(5s) profile 0-8 run - Run profile N (0-run next) *** profile 1-8 dtts source location|value - Profile DTTS source *** profile 1-8 dtts -20000-20000 - Manual profile DTTS value (us) *** # show service cotm --------------------------------- COTM general --------------------------------- Location source : Network Location : 29d 12' N / 122d 31' E Location set time : 11.Aug.2025 00:55:59 / 2s ago Report location : ON TX control : Local ------------------------------------- AMIP ------------------------------------- Enabled : ON Peer : 192.168.222.5:4001 vlan 0 State : UP Connected(Uptime) : +00:01:06 (+00:02:34 ) Reconnects : 1 Messages RX/TX : 115 78 Packets RX/TX : 223 282 Errors ACK/RETR : 0 0 Last RX message : s 1 1 Last TX message : L 1 1\nW 600\n ---------------------------------- ACU state ---------------------------------- Antenna ID : Manufacturer: Unknown Model: Unknown Antenna is functional : YES Antenna is disabled : NO Modem may transmit : YES Location valid : YES C/N requested : NO Alive interval (a) : 2s ----------------------------- Beam Switching state ----------------------------- Mode : OFF ----------------------------- Beam Switching config ---------------------------- Config load: 0% (8 / 8192)
Profile Restart Codes *0 - initial run profile or profile update *1 - no operation timeout restart *2 - redundancy to trying *3 - redundancy to fault *4 - manual run profile *5 - run profile received from NMS Code #6, no master (for hubless) Code #7, new network config *8 - station down(lost by HUB) Code #9 is empty not defined *10 - SCPC demod restart - no traffic *11 - redundancy config settings update *12 - profile switching from NMS *13 - redundancy switching from NMS *14 - master station number change from WWW *15 - timing watchdog in BD interrupt *16 - TLC remote unit down *17 - crosspol timer over *18 - DAMA station no info *19 - DAMA station down *20 - DAMA inr does not see station *21 - master station went down *22 - no stations timeout *23 - station timing restart *24 - hubless timing restart *25 - no slots received by TDMA for a long time *26 - mesh restart if bursts not received *27 - too many frame plans lost *28 - COTM TX control *29 - AMIP TX control *30 - clear interface CLI command *31 - CLI commands TX setup *32 - TTS confidence reached zero *33 - MF inroute detached from hub *34 - global level set from CLI *35 - edited site setup *36 - re-run profile after editing from HTTP *37 - run profile from SNMP *38 - demod down in SCPC mode *39 - restart from Thaicom protocol *40 - run profile from beam switching *41 - run profile after station tuning *42 - CLI commands RX setup *43 - CLI commands basic settings *44 - CLI commands settings *45 - MESH station got new config *46 - update profile *47 - too many CRC errors in hubless mode *48 - no bursts for a long time or DAMA *49 - TTS confidence is low *50 - Demodulator CRC restart *51 - station burst ID received is different from the expected station (bad timing?) *52 - wrong carrier *53 - Wrong timing on hubless station *54 - WBM is dead *55 - service traffic encryption mode changed *56 - restart from 'ge' cli command *57 - restart if station haven't been receiving adjustment info for a long time *58 - Mesh station is trying to switch to HDNA mode
查看接口信息 show interface ethernet Eth1 自动协商 interface ethernet 0 full 1 Eth1 百兆全双工 interface ethernet 100 full 1 Eth2 自动协商 interface ethernet 0 full 1 Eth2 百兆全双工 interface ethernet 100 full 1
(NMS)UHP# help
*** - command allows remote execution
---------- IP set-up
ip address IP_ADDR IP_MASK [1-4095] - Add IP address to interface [VLAN] ***
ip route IP_ADDR IP_MASK IP_ADDR [1-4095] - Add static route [VLAN] ***
ip map IP_ADDR IP_MASK ml|mm|mh|mp 1-64000 1-2040 [0-500] [0-2040] [0-4095] - Route network to modulator SVLAN STATION [Policy] [TrSh] [VLAN] ***
bridge map ml|mm|mh|mp 1-64000 1-2040 [0-500] [0-2040] [0-4095] - Bridge map SVLAN STATION [Policy] [TrSh] [VLAN] ***
svlan receive 1-64000 [0-4095] - Add SVLAN receive [VLAN] ***
ip delete IP_ADDR IP_MASK [0-4095] - Delete IP address, route or map [VLAN] ***
bridge delete 0-4095 - Delete bridge [VLAN] ***
svlan delete 1-64000 [0-4095] - Delete IP address, route or map [VLAN] ***
ip update off|on - Routing table update prevention ***
mcast off|static|igmp 1-30 - Multicast settings MODE TIMEOUT(min) ***
interface ethernet 0-1000 full|half 1-2 - Ethernet interface settings SPEED (0|10|100|1000(UHP-2XX only) M) DUPLEX PORT; SPEED 0 means AUTO ***
---------- System statistics
show profiles - Show profile settings
show interface ethernet|2demod|demod|modulator|network|wbm - Interface stats
show system - Show system parameters
show errors - Show device errors
show memory ram|flash|config - Show memory state
show service cotm|tuning - Services stats
clear counters all|ethernet|2demod|demod|modulator|tdma|ip|redtl|profile|acc|crypto|dhcp|snmp|dns|nms|gtp|cotm|wbm - Reset stats ***
---------- Protocol statistics
show ip [0-4096] - Routing table [VLAN] 4096-untagged
show arp - ARP table
show rtp - RTP header compression statistics
show snmp - Display SNMP parameters
show dhcp - Display DHCP parameters
show multicast - Display multicast parameters
show acceleration all|stat|sessions|buf|rem STRING - TCP acceleration stats
show shaper - Print Traffic Shaper statistics
show nat - Print NAT statistics
show red - Display stations redundancy table
show mac STRING - MAC table [pX|mac]
clear mac STRING - Clear MAC table [pX|mac] ***
---------- Satellite network statistics
show net - Display network state
show stations traffic priority [1-16000] - Display stations traffic by priority
show stations traffic [1-16000] - Display stations traffic statistics
show stations rf [1-16000] - Display stations RF statistics
show stations [1-16000] - Show station statistics
show mf - Show MF inroutes statistics
show modcods - Show modcods ACM statistics
show tlc - Show SCPC TLC statistics
show backup - Show redundancy backup statistics
show nms - Show NMS statistics
---------- Demodulator utilities
demod phase-graph [0-8] - Display phase constellation
demod bert qpsk|re|data - Bit error rate meter
demod antenna [1-2] [0-800] [0-800] - Antenna pointing mode [RF min] [RF max]
---------- Auxiliary RF control
modulator tx off|on - Tx carrier control ***
modulator level 10-460 - TX power level (x -0.1 dBm) ***
modulator global cn [0-30] - Set global level from far end C/N (0-disable) ***
modulator inversion off|on - Spectrum inversion ***
modulator reference off|on - Modulator 10 MHz output ***
modulator power off|on - Modulator 24V BUC power ***
modulator tlc level 10-460 - Max TLC TX level (x -0.1 dBm) ***
modulator tlc off|on - Automatic transmit level control ***
demod lnb power off|on - LNB power control ***
demod reference off|on - TDMA RX connector 10 MHz output ***
demod inversion 1-2 off|on - Demodulator inversion [1|2] [off|on] ***
rf lo 0-33000000 0-33000000 0-35000000 - RF LO frequencies RX1, RX2, TX ***
---------- Profile and stations table control
profile 0-8 copy 1-8 - Copy profile N1 (0-active) to profile N2 ***
profile 0-8 timeout 10-250 - Timeout ***
profile 1-8 type auto|manual none|scpc|starrem|damarem|hmesh|crosspol|slave|master|asic - Mode ***
profile 1-8 autorun on|off - Autorun ***
profile 1-8 crosspol 950000-32000000 0-65535 - CrossPol FREQ DURATION ***
profile 1-8 rx d2 950000-32000000 300-200000 - Rx2 FREQ SYMRATE(200000(200X)/64995(200)) ***
profile 1-8 rx 950000-32000000 300-200000 - Rx FREQ SYMRATE(200000(200X)/64995(200)) ***
profile 1-8 tx 950000-32000000 300-64995 1-127 - Tx FREQ SYMRATE(64000(200X)/64995(200)) MODCOD(1-127(200X)/2-28(200)) ***
profile 1-8 modulator on|off 10-460 - Modulator TX [on|off] TXLEVEL ***
profile 1-8 tlc on|off scpctlc on|off 1-36 [1-239] STRING - TLC [on|off] SCPC:TLC [on|off] MAXTXLVL [SCPC:DesiredC/N] [SCPC:peer IP] ***
profile 1-8 hubless tdma 16-252 2-15 1-2040 - TDMA FRLEN SLLEN STNUM ***
profile 1-8 hubless rf 950000-32000000 950000-32000000 100-8000 1-12 - Hubless RXFR TXFR SYMRATE MODCOD ***
profile 1-8 dama 1-2 1-2040 1-99999999 1-99999999 950000-32000000 250-32000 1-127 off|on 20|05 1-360 off|on|purecarrier - CH STN SN RSN FR SR MODCOD(1-127(200X)/2-28(200)) PILOTS ROFF TXLVL TXMODE ***
profile 1-8 acm on|off 1-127 0-59 - ACM [on|off] MAXMODCOD(1-127(200X)/2-28(200)) THRESHOLD ***
profile 1-8 demodulator polarization 13|18 - LNB voltage 13|18 V ***
profile 1-8 demodulator 1-2 off|on 1-2 - DemX ON|OFF RX1|RX2 ***
profile 1-8 satellite 0-179 0-59 East|West - Satellite position (DEG MIN) ***
profile 0-8 run - Run profile N (0-run next) ***
profile 1-8 dtts source location|value - Profile DTTS source ***
profile 1-8 dtts -20000-20000 - Manual profile DTTS value (us) ***
station table 0-2040 on|off 0-100000 0-680 0-3 on|off - Add/edit station (stnum>0 on serialnum shaper rq_profile TCPA); station table 0 on 1-2040 ... - set size of table (stnum) ***
---------- Location and timing control
timing source location|value|measure - Timing source ***
station dtts source location|value - Station DTTS source ***
station location 0-89 0-59 north|south 0-179 0-59 east|west - Location LAT LON (DEG MIN) ***
station dtts -20000-20000 - Manual station DTTS value (us) ***
---------- Overall control
admin - Switch to Administrator mode
exit - Log out from console ***
clear interface ethernet|demod|mod|wbm|tdma - Reinitialize interface ***
clear arp-table - Purge contents of ARP table ***
clear dhcp - Purge contents of DHCP table ***
clear tuning - Clear station tuning corrections ***
time set 0-24 0-60 1-31 1-12 0-99 - Set date/time HH MM DD MM YY ***
time zone -12-12 - Set time zone ***
unit key 0-15 [0-65535] [0-65535] [0-65535] - Set features key
watchdog reset|interrupt - Watchdog timer overflow action ***
reboot stop - Stop delayed reboot ***
reboot auto 3-250 - Auto reboot device [delay in minutes] ***
reboot [0-1000] - Reboot device [delay in minutes] ***
network command 0-2000000000 STRING - Command to terminal(s) by SN(11111111 - broadcast)
network software send 1-3 [32-500] - Send SW from RAM to stations FL_BANK [BW K]
msg STRING - Output text message ***
set page off|on - Set output paging ON|OFF ***
custom [1-96] -2000000000-2000000000 - Customization ***
---------- Logging & debug
show log - Display logs
clear log - Purge logs
logging stations off|on - Logging events "Station UP/DOWN"
debug show [0-10000000] - Print debug [start record] ***
debug mode off|on|restart|wrap|nowrap|profile-stop|on-persist|off-persist - Debug control ***
debug output off|console|network [1-65535] - Debug output control ***
debug system profile|lan|demodulator|modulator|tasks|buffers|config|interrupts|crypto 0x0-0xFFFF [1-10000000] - ***
debug protocol snmp|dhcp|arp|nat|rip|ntp|rtp|tftp|igmp|http|icmp|telnet|ppp|nms|roaming|service 0x0-0xFFFF - ***
debug service redundancy|tlc|acm|cotm|monitoring|script|policy|shaper|dns|spectrum|csim|asi|calibration|dualband|log|debug|tuning|egw 0x0-0xFFFF [1-10000000] - ***
debug tdma frameplan|bandwidth|adjustment|reception|config|protocols|tts|bursts|mf 0x0-0xFFFF 0-65535 0-65535 [0-65535] - ***
debug tcpa 0x0-0xFFFF - ***
debug off - Debug - off all ***
---------- Diagnostics
ping IP_ADDR [1-1000000] [40-2000] [1-10000] [0-4095] - IP Num Len Int/ms VLAN
traffic analyzer off|on - Traffic analyzer for trgen.
traffic-generator off - Disable traffic generator
traffic-generator IP_ADDR 1-50000 36-2000 [0-4095] [1-50000] [36-2000] - IP Pps Len [VLAN] [PpsMax] [PpsMin]
---------- Configuration and SW image management
tftp-server IP_ADDR 0-4095 - TFTP server access
config load default all|global|ip|profile|qos|stations|nat - Load default config ***
config load tftp STRING - Load config from TFTP
config save tftp STRING - Save current config to TFTP
config load 0-1 - Load config from specified profile ***
config save 0-1 - Save current config to specified profile ***
image load tftp STRING - Load image by TFTP to RAM
image load xmodem - Load image with X-modem to RAM buffer
image load flash - Copy image from flash to RAM
image write - Write image from RAM to Flash
erase flash - Erase flash bank
---------- Boot control
show boot - Show software boot options
boot main 0-2 0-1 - Main boot profile FLASH_BANK(0-auto) CONF_BANK ***
boot temp 0-2 0-1 - Temp boot profile FLASH_BANK(0-none) CONF_BANK ***
boot fallback timeout 1-10000 - Temp image auto fallback period (min) ***
boot fallback reason uptime|link-up - Auto fallback reason ***
boot fallback stop - Abandon auto fallback ***
---------- Crypto settings and utilities
crypto key [1-256] STRING - Set key INDEX KEY_HEX_STRING
crypto service off|on 1-255 - Set service traffic encryption ON|OFF KEY_IND
show crypto - Show crypto statistics
---------- Help
help - Print this help
NMS)UHP#
SNMP settings
| Version | |
| Privacy mode | |
| Access IP 1 | |
| Access IP 2 | |
| Read community | |
| Write community | |
| Username | |
| Auth password | |
| Privacy password |
snmpset -V NET-SNMP version: 5.5 TYPE: one of i, u, t, a, o, s, x, d, b i: INTEGER, u: unsigned INTEGER, t: TIMETICKS, a: IPADDRESS o: OBJID, s: STRING, x: HEX STRING, d: DECIMAL STRING, b: BITS U: unsigned int64, I: signed int64, F: float, D: double ##### 发送命令 snmpset -v 2c -c private 192.168.222.1 .1.3.6.1.4.1.8000.22.1.3.0 s "clear arp-table" snmpset -v 2c -c private 192.168.222.1 .1.3.6.1.4.1.8000.22.1.3.0 s "clear dhcp" snmpset -v 2c -c private 192.168.222.1 .1.3.6.1.4.1.8000.22.1.3.0 s "config save" ##### RX1 的接收信噪比，单位 0.1dB snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.2.1.0 SNMPv2-SMI::enterprises.8000.22.2.1.0 = INTEGER: 133 ##### RX1 的接收频偏，单位 1000Hz = KHz snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.2.2.0 SNMPv2-SMI::enterprises.8000.22.2.2.0 = INTEGER: -17 ##### RX1 的接收电平，显示需要加上负号，单位 -0.1dBm snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.2.3.0 SNMPv2-SMI::enterprises.8000.22.2.3.0 = Gauge32: 183 ##### RX2 的接收信噪比，单位 0.1dB snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.3.1.0 SNMPv2-SMI::enterprises.8000.22.3.1.0 = INTEGER: 0 ##### RX2 的接收频偏，单位 1000Hz = KHz snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.3.2.0 SNMPv2-SMI::enterprises.8000.22.3.2.0 = INTEGER: -50687 ##### RX2 的接收电平，显示需要加上负号，单位 -0.1dBm snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.3.3.0 SNMPv2-SMI::enterprises.8000.22.3.3.0 = Gauge32: 80
##### TX 的发射电平 OutTxLevel ，显示需要加上负号，单位 -0.1dBm snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.4.6.1.0 SNMPv2-SMI::enterprises.8000.22.4.6.1.0 = Gauge32: 373 ##### TX 的发射电平偏差 txLevelDelta ，显示需要加上负号，单位 -0.1dBm ##### txLevelDelta(-12.3dBm) = OutTxLevel(-37.3dBm) - txSetLevel(-25.0dBm) snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.4.6.2.0 SNMPv2-SMI::enterprises.8000.22.4.6.2.0 = INTEGER: 123 ##### TX 的最大TLC发射电平偏差 txMaxLevel ，单位 -0.1dBm ##### txMaxLevel(-20.0dBm) > txSetLevel(-25.0dBm) > OutTxLevel(-37.3dBm) snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.4.6.3.0 SNMPv2-SMI::enterprises.8000.22.4.6.3.0 = INTEGER: 200 ##### 小站Modem的状态 INTEGER {off(0),init(1),noConfig(2),useConfig(3),redundant(4),startRX(5), cotmPointing(6),startHubTX(7),noRX(8),identify(9),getNetConfig(10), calcDelays(11),startTDMA(12),startTX(13),acquisition(14),adjustment(15), noStations(16),operation(17)} ##### operation(17) 为 正常入网状态 snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.5.5.1.0 SNMPv2-SMI::enterprises.8000.22.5.5.1.0 = INTEGER: 17 ##### 小站Modem的温度 snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.8.1.0 SNMPv2-SMI::enterprises.8000.22.8.1.0 = INTEGER: 31 ##### 小站Modem的负载率 snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.8.2.0 SNMPv2-SMI::enterprises.8000.22.8.2.0 = Gauge32: 21 ##### 小站Modem的缓存率 snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.8.3.0 SNMPv2-SMI::enterprises.8000.22.8.3.0 = Gauge32: 2 ##### 小站Modem的备用状态 GAUGE32 {IDLE(0),BACKUP(1),FAULT(2),TRYING(3),ACTIVE(4),OFF(5)} ##### OFF(5) 为 关闭状态 snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.8.4.0 SNMPv2-SMI::enterprises.8000.22.8.4.0 = Gauge32: 5
##### 小站Modem的固件发布版本 ##### 50790707 = 0x03070133 <=> 0x03,0x07,0x01,0x33 = Ver: 3.7.1.51 snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.8.5.0 SNMPv2-SMI::enterprises.8000.22.8.5.0 = Gauge32: 50790707 ##### 小站Modem的固件发布日期 ##### 134744038 = 0x080807E6 <=> 0x08,0x08,0x07E6 = Ver: 08.08.2022 snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.8.6.0 SNMPv2-SMI::enterprises.8000.22.8.6.0 = Gauge32: 134744038 ##### 小站Modem的软件版本 snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.9.1.0 SNMPv2-SMI::enterprises.8000.22.9.1.0 = Gauge32: 10 ##### 小站Modem的序列号 ##### 1074300739 = 0x40088743 <=> 0x40,0x08,0x87,0x43 = SN: 40088743 snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.9.2.0 SNMPv2-SMI::enterprises.8000.22.9.2.0 = Gauge32: 1074300739 ##### 接收电平 inputLevel ，显示需要加上负号，单位 -0.1dBm snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.9.3.0 SNMPv2-SMI::enterprises.8000.22.9.3.0 = Gauge32: 183 ##### 接收信噪比 rxState，单位 0.1dB snmpget -v 2c -c public 192.168.222.1 .1.3.6.1.4.1.8000.22.9.4.0 SNMPv2-SMI::enterprises.8000.22.9.4.0 = Gauge32: 130
============= End
浙公网安备 33010602011771号