1 ************************************************************************************************************************* A 0000
* SYSTEM COMPLETION CODE ( SXXX ) * A 0100
************************************************************************************************************************* A 0200
===== < CODE = A13 > ===== AA13 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ AA13 0100
| TAPE I/O ERROR ( IEC151I ) | * HARDWARE | * RERUN | AA13 0200
| | | * RECREATE DATA SET | AA13 0300
| | OFTEN OCCURRED DURING WRITING WITH | * LABEL=(,SL) | AA13 0400
| |DISP=MOD OR READING MULTI VOLUME DATA | | AA13 0500
| |SET. | | AA13 0600
+---------------------------------------+---------------------------------------+---------------------------------------| AA13 1000
===== < CODE = B37 > ===== AB37 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ AB37 0100
| SPACE SHORTAGE ( IEC030I ) | * PHISICALLY SPACE SHORTAGE | * CHANGE PRIVATE VOLUME | AB37 0200
| | * NO MORE SPACE IN THE VOLUME | * SPECIFY MULTI VOLUME | AB37 0300
| | * EXTENTION 16 OVER | * UNIT=SYSDA ===> UNIT=(DISK2,6) | AB37 0400
| | * PRIMARY SPACE NOT AVAILABLE | | AB37 0500
| | * WORK SPACE NOT AVAILABLE | | AB37 0600
+---------------------------------------+---------------------------------------+---------------------------------------| AB37 1000
===== < CODE = C03 > ===== AC03 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ AC03 0100
| ENTER STOP COMMAND WHEN BMP REPLY | CLOSE MACRO INSTRUCTION NOT EFFECTIVE | USE STOP STATEMENT IN PROGRAM | AC03 0200
+---------------------------------------+---------------------------------------+---------------------------------------| AC03 1000
===== < CODE = D03 > ===== AD03 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ AD03 0100
| TAPE I/O ERROR | HARDWARE | RERUN | AD03 0200
+---------------------------------------+---------------------------------------+---------------------------------------| AD03 1000
===== < CODE = D37 > ===== AD37 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ AD37 0100
| EOV : NO SECONDARY QUANTITY | PRIMARY SPACE OVER WHEN NOT SPECIFIED | * INCREASE PRIMARY SPACE | AD37 0200
| ( IEC031I ) |SECONDARY SPACE | * SPECIFY SECONDARY SPACE | AD37 0300
+---------------------------------------+---------------------------------------+---------------------------------------| AD37 1000
===== < CODE = E00 > ===== AE00 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ AE00 0100
| ERROR DURING EXCP | CSA SHORTAGE | DECREASE POOL SIZE IN CSA | AE00 0200
+---------------------------------------+---------------------------------------+---------------------------------------| AE00 1000
===== < CODE = E23 > ===== AE23 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ AE23 0100
| ERROR DURING WTOR MACRO INSTRUCTION | OPERATOR ENTER REPLY COMMAND AFTER | RERUN | AE23 0200
| |DISPLAYED NORMAL END MESSAGE | | AE23 0300
+---------------------------------------+---------------------------------------+---------------------------------------| AE23 1000
===== < CODE = E37 > ===== AE37 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ AE37 0100
| * EOV : PDS OUT OF SPACE | * SPACE SHORTAGE IN PDS | * CONDENCE | AE37 0200
| * INSUFFICIENT VOLUME | * NO AVAILABLE SPACE IN THE VOLUME | * DELETE NOT USED DATA SET | AE37 0300
| * ( IEC032I ) | | * SPECIFY OTHER VOLUME | AE37 0400
+---------------------------------------+---------------------------------------+---------------------------------------| AE37 1000
===== < CODE = 0CA > ===== A0CA 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A0CA 0100
| DECIMAL-OVERFLOW | FIXED OVERFLOW | INCREASE FIELD LENGTH | A0CA 0200
+---------------------------------------+---------------------------------------+---------------------------------------| A0CA 1000
===== < CODE = 0C1 > ===== A0C1 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A0C1 0100
| OPERATION EXCEPTION | * PROGRAM ERROR --- DESTROY OTHER AREA| | A0C1 0200
| | ( EX. TABLE OVER )| | A0C1 0300
| | * ERROR WHEN LINK | | A0C1 0400
| | * GO UNRESOLVED MODULE | | A0C1 0500
| | * NO-CALL EXTERNAL MODULE | | A0C1 0600
| | * HARDWARE | * RERUN | A0C1 0700
| | * OTHER | | A0C1 0800
| | * MORE LONGER BLKSIZE FILE ARRANGED| * REARRANGE DD STATEMENTS IN ORDER OF | A0C1 0900
| | LATER POSITION WHEN MULTI INPUT | DECREASE OF BLKSIZE | A0C1 1000
| | FILE CONCATINATION | | A0C1 1100
+---------------------------------------+---------------------------------------+---------------------------------------| A0C1 1200
===== < CODE = 0C4 > ===== A0C4 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A0C4 0100
| PROTECTION EXCEPTION | * UNKNOWN | * RERUN | A0C4 0200
| | * NOT SPECIFIED SYMBOLIC PARAMETER | * SPECIFY IT IN JOB CARD | A0C4 0300
| | IN JOB CARD WHICH USED IN STEP | | A0C4 0400
| | * INVALID PARAMETER IN EXTOSUT | * PARM='IEHPROGM,X=X' | A0C4 0500
| | * ABEND IN SVC WHEN BY-PASS BECAUSE | | A0C4 0600
| | OF LOG TAPE DATA CHECK | | A0C4 0700
| | * FOUR TIMES SPECIFIED '/STA,LINE,ALL'| | A0C4 0800
| | * TOO LONG MASSAGE INPUT FOR MOP | | A0C4 0900
| | ANALYSIS COMMAND | | A0C4 1000
+---------------------------------------+---------------------------------------+---------------------------------------| A0C4 1100
===== < CODE = 0C6 > ===== A0C6 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A0C6 0100
| SPECIFICATION EXCEPTION | NOT FOUND CONTROL CARD IN PROGM1 | CONTROL CARD SET UP | A0C6 0200
+---------------------------------------+---------------------------------------+---------------------------------------| A0C6 1000
===== < CODE = 0C7 > ===== A0C7 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A0C7 0100
| DATA EXCEPTION | * ALL '0' IN DECIMAL ARITHMETIC FIELD | RECREATE FILE | A0C7 0200
| | * INVALID PACKED DATA WHEN MOP LOGON | | A0C7 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A0C7 1000
===== < CODE = 0F3 > ===== A0F3 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A0F3 0100
| MACHINE CHECK | HARDWARE | RERUN | A0F3 0200
+---------------------------------------+---------------------------------------+---------------------------------------| A0F3 1000
===== < CODE = 000 > ===== A000 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A000 0100
| * SORT WORK TOO SMALL | * SORTWORK SPACE SHORTAGE ( U0046 ) | * INCREASE SP PARAMETER | A000 0200
| * STEP SYNTAX ERROR | * WRONG LOAD MODULE | | A000 0300
| | * NOT SPECIFIED OPEN/CLOSE FOR 0 | * OPEN/CLOSE STATEMENT ADDITON | A000 0400
| | RECORD | | A000 0500
+---------------------------------------+---------------------------------------+---------------------------------------| A000 1000
===== < CODE = 001 > ===== A001 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A001 0100
| CHECK/GET/PUT : I/O ERROR ENCOUNTERED | * NOT SPECIFIED OPEN BUT CLOSE FOR 0 | * OPEN STATEMENT ADDITION | A001 0200
| ( IEC020I ) | RECORD | | A001 0300
| | * INVALID DCB SPECIFIED | * CHANGE DCB | A001 0400
| | * HARDWARE | * RERUN | A001 0500
+---------------------------------------+---------------------------------------+---------------------------------------| A001 1000
===== < CODE = 002 > ===== A002 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A002 0100
| | * REFFER NOT CREATED TABLE DATA | * CREATE TABLE | A002 0200
| ( IEC036I ) | * DCB DIFFERENCE SORTIN FROM SORTOUT | * SPECIFY SAME DCB | A002 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A002 1000
===== < CODE = 013 > ===== A013 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A013 0100
| * OPEN DCB INCORRECT | * HARD ERROR | * SPECIFY OTHER TAPE UNIT/WORK DISK | A013 0200
| * NO MEMBER FOUND | | | A013 0300
| * NO DIRECTORY ALLOCATION | * -20 DIFFERENCE BLKSIZE FROM OTHER | * CORRECT DCB | A013 0400
| | DCB PARAMETER | | A013 0500
| * ( IEC141I ) | * -50 NOT SPECIFIED OUTPUT OPTION | * SPECIFY OUTPUT OPTION | A013 0600
| | TO THE FILE ALLOCATED PRINTER | | A013 0700
| | * -60 LRECL NOT EQUAL TO BLKSIZE IN | * LRECL = BLKSIZE | A013 0800
| | RECFM=F DATA SET | | A013 0900
| | * -64 ERROR IN NULL FILE EXCEPT FOR | * USE REAL FILE | A013 1000
| | QSAM,BSAM | * USE QSAM,BSAM | A013 1100
| | * ? DISK TO DISK('DD') COPY IN | * COPY BY IEBGENER | A013 1200
| | RECFM=FBA DATA SET | | A013 1300
+---------------------------------------+---------------------------------------+---------------------------------------| A013 1400
===== < CODE = 028 > ===== A028 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A028 0100
| I/O ERROR ATTEMPTING PAGE-IN OPERATION| I/O ERROR (PAGING) | RERUN | A028 0200
+---------------------------------------+---------------------------------------+---------------------------------------| A028 1000
===== < CODE = 03B > ===== A03B 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A03B 0100
| OPEN : NO RECORDS FROM ISAM/VSAM FILE | * 0 RECORD ISAM FILE | * REGENERATE FILE | A03B 0200
| | * INVALID PARAMETER WHEN DEFINE VSAM | * CORRECT PARAMETER | A03B 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A03B 1000
===== < CODE = 039 > ===== A039 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A039 0100
| SCAN : END OF DATA | PREVIOUS STEP RETURNED 'CODE 0008' | EXTEND PRIMARY SPACE OF DATA BASE. | A039 0200
| | FOR DATA BASE SPACE BEING INSUFFICIENT| | A039 0300
| | . | | A039 0400
| | THIS ERROR OCCURRED WHEN THAT FILE | | A039 0500
| | WAS RETRIEVED( GET ) AT THE FOLLOWING | | A039 0600
| | STEP. | | A039 0700
| | | | A039 0800
+---------------------------------------+---------------------------------------+---------------------------------------| A039 0900
===== < CODE = 052 > ===== A052 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A052 0100
| VSAM FILE : I/O MACRO ERROR | MORE THAN TWO USER PROGRAMS UPDATED | CHANGE THE OPERATION SEQUENCE. | A052 0200
| | VSAM FILE(HAVING DISP=SHR) AT THE | | A052 0300
| | SAME TIME. | | A052 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A052 0500
===== < CODE = 071 > ===== A071 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A071 0100
| OPERATOR PRESSED THE RESTART KEY. | OPERATOR PRESSED THE RESTART BUTTON | RERUN | A071 0200
| | DURING EXECUTION OF A USER PROGRAM. | | A071 0300
| | | | A071 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A071 0500
===== < CODE = 084 > ===== A084 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A084 0100
| | THE ERROR OCCURRED WHILE ATTEMPTING | RE-DEFINE CLUSTER, AND LOAD. | A084 0200
| | TO LOAD A DATA WITH OVERRAPPING | | A084 0300
| | TO VSAM DATA SET USING NON-REUSE | | A084 0400
| | OPTION. | | A084 0500
| | | | A084 0600
+---------------------------------------+---------------------------------------+---------------------------------------| A084 0700
===== < CODE = 122 > ===== A122 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A122 0100
| OPERATOR CANCEL | * PROGRAM LOOP | | A122 0200
| | * WAITING FOR RESOURCES | | A122 0300
| | * CPU 100% | | A122 0400
| | * SIGN ON MSG HAVE BEEN FULL | * START-STOP | A122 0500
| | | | A122 0600
+---------------------------------------+---------------------------------------+---------------------------------------| A122 1000
===== < CODE = 138 > ===== A138 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A138 0100
| TWO ENQ MACRO WERE ISSUED FOR THE | THE VSAM FILE WHICH GENERATED WITH | TO SPECIFY STEPCAT/JOBCAT. | A138 0200
| SAME RESOURCE IN THE SAME TASK. | STEPCAT/JOBCAT HAVE BEEN RETRIEVED | | A138 0300
| | WITHOUT STEPCAT/JOBCAT. | | A138 0400
| | | | A138 0500
+---------------------------------------+---------------------------------------+---------------------------------------| A138 1000
===== < CODE = 2F3 > ===== A2F3 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A2F3 0100
| THE JOB WAS RUNNING WHEN A SYSTEM | SYSTEM LOOP. | IPL | A2F3 0200
| FAILURE OCCURRED. | | | A2F3 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A2F3 0400
===== < CODE = 212 > ===== A212 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A212 0100
| AN ERROR OCCURRED DURING THE | TABLE OVER | MAKING CORRECTION, AND RERUN | A212 0200
| EXECUTION OF SVC18. | | | A212 0300
| (IEC909I) | | | A212 0400
| | | | A212 0500
+---------------------------------------+---------------------------------------+---------------------------------------| A212 1000
===== < CODE = 213 > ===== A213 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A213 0100
| DATA SET OPEN ERROR | * THE DATA SET COULD NOT BE FOUND ON | RE-CREATION THE FILE | A213 0200
| ( DATA SET NOT FOUND ) | THE VOLUME SPECIFIED BY THE DD | | A213 0300
| ( IEC143I ) | STATEMENT OR IN THE CATALOG. | | A213 0400
| | * THE DIFERENT ATTRIBUTE WAS SPECIFIED| | A213 0500
| | TO THE SAME FILE BY ROUTE AND CHILD | | A213 0600
| | MODULE. | | A213 0700
| | * OPEN ABEND BY THE CASE OF USING | | A213 0800
| | EXTERNAL SUBROUTINE. | | A213 0900
| | | | A213 1000
+---------------------------------------+---------------------------------------+---------------------------------------| A213 1100
===== < CODE = 214 > ===== A214 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A214 0100
| CAN NOT READ A DATA SET ON MAGNETIC | I/O ERROR | REGENERATE A DATA SET ON TAPE | A214 0200
| TAPE (IEC210I) | | | A214 0300
| | | | A214 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A214 0500
===== < CODE = 222 > ===== A222 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A222 0100
| OPERATOR CANCEL | * PROGRAM LOOP | FIND OUT WHY THE OPERATOR CANCELED | A222 0200
| | * WAITING FOR RESOURCES | YOUR JOB, AND MAKE ANY NECESSARY | A222 0300
| | ( DASD SPACE / DEVICES ) | CORRECTIONS. THEN RERUN THE JOB. | A222 0400
| | | | A222 0500
+---------------------------------------+---------------------------------------+---------------------------------------| A222 0600
===== < CODE = 233 > ===== A233 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A233 0100
| INVALID PARAMETER HAVE BEEN PASSED | SYSTEM ERROR | AFTER IPL, THEN RERUN THE JOB. | A233 0200
| TO SVC DUMP. | | | A233 0300
| | | | A233 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A233 0500
===== < CODE = 237 > ===== A237 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A237 0100
| LABEL VERIFICATION ERROR | * THE BLOCK COUNT IN THE DCB DOES | REGENARATE A DATA SET ON TAPE. | A237 0200
| (IEC023I) | NOT MATCH THAT IN THE TRAILER LABEL.| | A237 0300
| | * THE DSNAME IN A HEADER LABEL DOES | | A237 0400
| | NOT MATCH THAT IN THE JFCB. | | A237 0500
| | | | A237 0600
+---------------------------------------+---------------------------------------+---------------------------------------| A237 0700
===== < CODE = 271 > ===== A271 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A271 0100
| PGFIX OR PGFREE REQUESTED AND CALL | IMS/360 PROGRAM EXECUTED ON MVS | | A271 0200
| IS NOT AUTHORIZED. | MACHINE. | | A271 0300
| | | | A271 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A271 0500
===== < CODE = 30A > ===== A30A 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A30A 0100
| FREE MAIN, SVC ERROR | PROBABLY USER ERROR. | MAKING CORRECTIONS, AND EXECUTE THE | A30A 0200
| | (EX. TABLE OVER ) | JOB STEP AGAIN. | A30A 0300
| | | | A30A 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A30A 0500
===== < CODE = 301 > ===== A301 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A301 0100
| WAIT MACRO INSTRUCTION SPECIFIED AN | TO HAVE READ DUMMY DATA BASE. | CHANGE THE PROBEM PROGRAM, AND THEN | A301 0200
| ECB WHOSE WAIT FLAG WAS ALREADY ON. | | EXECUTE THE JOB STEP AGAIN. | A301 0300
| | | | A301 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A301 0500
===== < CODE = 314 > ===== A314 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A314 0100
| CLOSE I/O ERROR FOR A DATA SET ON A | MSS TROUBLE | RERUN THE JOB. | A314 0200
| DASD. (IEC211I) | | | A314 0300
| | | | A314 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A314 0500
===== < CODE = 322 > ===== A322 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A322 0100
| TIME EXCEEDED. | * PROGRAM ENDLESS LOOP. | * CORRECT THE PROGRAM ERRORS. | A322 0200
| | * PROGRAM HAS THE USELESS AND TIME- | * IF NO ERRORS FOUND, SPECIFY A LONGER| A322 0300
| | EATIG LOGICS. | TIME IN THE TIME PARAMETER. | A322 0400
| | * JOB HAS A GREAT MANY STEPS. | | A322 0500
+---------------------------------------+---------------------------------------+---------------------------------------| A322 1000
===== < CODE = 400 > ===== A400 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A400 0100
| DCB ADDRESS IN THE DEB DIFFERS FROM | * ISAM FILE,IN CASE OF WORK,MUST BE | * CHNGE JCL WITH USING 'VOL=REF=*.XX' | A400 0200
| DCB ADDRESS IN THE IOB. | ON THE SAME VOLUME. | SPECIFICATION. | A400 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A400 1000
===== < CODE = 413 > ===== A413 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A413 0100
| MSS FAILURE IN ACQUIRE CODE = NNN | * 0C8 : THE FIRST DATA SET WHICH | * EXCHANGE THE ORDER. | A413 0200
| (IEC145I) | CONCATINATED IS SMALLER THAN | * OVERRIDE DCB WHICH SPECIFY THE LARGE| A413 0300
| | THE SECOND. | BLKSIZE ON THE FIRST DD STATEMENT. | A413 0400
| | * 094 : MSS ERROR. | * RERUN AFTER THE MSS RECOVERY. | A413 0500
+---------------------------------------+---------------------------------------+---------------------------------------| A413 1000
===== < CODE = 522 > ===== A522 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A522 0100
| ALL TASKS IN JOB STEP EXCEEDED WAIT | * HARD | | A522 0200
| TIME. | * MSS MOUNT PENDING. | | A522 0300
| | * DISK I/O ERROR. | | A522 0400
| | * OPERATION | | A522 0500
| | * OPERATOR DID NOT KEY IN REPLY. | | A522 0600
+---------------------------------------+---------------------------------------+---------------------------------------| A522 1000
===== < CODE = 613 > ===== A613 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A613 0100
| OPEN I/O ERROR FOR A TAPE DATA SET. | * HARD | * CHANGE THE TAPE UNIT. | A613 0200
| (IEC147I) | | | A613 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A613 1000
===== < CODE = 637 > ===== A637 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A637 0100
| THE ERROR OCCURED AT AN END-OF-VOLUME | * I/O ERROR | * RE-CATALOGUE. | A637 0200
| FOR A DATA SET ON TAPE OR AN END-OF-V | | | A637 0300
| OLUME DURING CONCATINATION. | | | A637 0400
| (IEC026I) | | | A637 0500
+---------------------------------------+---------------------------------------+---------------------------------------| A637 1000
===== < CODE = 706 > ===== A706 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A706 0100
| LINK ERROR OF EXCUTION OF LINK,LOAD, | * THE REQUESTED LOAD MODULE WAS MARKED| * RECATALOGUE AFTER CORRECTING PGM | A706 0200
| ATTACH,XCTL MACRO. | BY THE LINKAGE EDIT AS NOT EXCUTABLE| ERROR. | A706 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A706 1000
===== < CODE = 722 > ===== A722 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A722 0100
| THE JOBS OUTPUT LIMIT IS EXCEEDED. | * ACTUAL OUTPUT LINE COUNT IS OVER THE| * SPECIFY APPROPRIATE LIMIT COUNT IN | A722 0200
| CANCELED BY JES2. | OUTPUT LIMIT COUNT SPECIFIED BY THE | THE JOBPARM. | A722 0300
| | JOBPARM. | | A722 0400
| | * JOB IS CANCELED BECAUSE OF OPERATION| | A722 0500
| | CODE SET '3X' ON PRODUCTION JOB. | | A722 0600
+---------------------------------------+---------------------------------------+---------------------------------------| A722 1000
===== < CODE = 737 > ===== A737 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A737 0100
| MSS MOUNT FAILURE. | * I/O ERROR. | | A737 0200
| * MSS FAILURE IN AQUIRE ABEND. | * I/O ERROR WHEN RESERVE THE SPACE ON | * RERUN AFTER THE MSS RECOVERY. | A737 0300
| | MSS. | | A737 0400
| * MSS MOUNT FAILURE FOR VOL=NNNNNN | * ERROR WHEN MOUNT MSS. | | A737 0500
| * VSAM PHYSICAL ERROR. | | * VSAM RELOAD AFTER THE MSS RECOVERY. | A737 0600
+---------------------------------------+---------------------------------------+---------------------------------------| A737 1000
===== < CODE = 80A > ===== A80A 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A80A 0100
| ERROR OF R-FORM GETMAIN MACRO INSTRUC-| * LACK OF REGION SIZE. | * ADD TO REGION SIZE. | A80A 0200
| TION EXCUSION. | * LACK OF ISA SIZE. | * ADD TO ISA SIZE. | A80A 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A80A 1000
===== < CODE = 804 > ===== A804 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A804 0100
| ERROR OF EU,LU,OR VU FORM GETMAIN MAC-| * LACK OF REGION SIZE. | * ADD TO REGION SIZE. | A804 0200
| RO INSTRUCTION EXCUSION. | * LACK OF ISA SIZE. | * ADD TO ISA SIZE. | A804 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A804 1000
===== < CODE = 806 > ===== A806 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A806 0100
| PROGRAM MISSING. | * PROGRAM ENTRY POINT IS NOT FOUND IN | * RECATALOG. | A806 0200
| | THE INDICATED LIBRARY. | * CHANGE MEMBER NAME. | A806 0300
| | | * CHANGE STEPLIB OR JOBLIB NAME. | A806 0400
| | * SERCH MEMBER WHEN LIBRARY IS BEING | | A806 0500
| | CONDENSED. | | A806 0600
+---------------------------------------+---------------------------------------+---------------------------------------| A806 1000
===== < CODE = 813 > ===== A813 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A813 0100
| SORT OPEN ERROR. | * SYMBOLIC SPECIFINING ERROR. | * CORRECT SYMBOLIC. | A813 0200
| (IEC149I) | | | A813 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A813 1000
===== < CODE = 822 > ===== A822 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A822 0100
| REGION UNAVAILABLE. | * | * SIMPLE RERUN. | A822 0200
+---------------------------------------+---------------------------------------+---------------------------------------| A822 1000
===== < CODE = 837 > ===== A837 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A837 0100
| THE ERROR OCCURED AT AN END-OF-VOLUME | * 1 FILE EXTENDED OVER 5 TAPE VOLUMES.| * CHANGE FROM 1200FT TO 2400FT. | A837 0200
| FOR A SEQUENTIAL DATA SET. | | | A837 0300
| (IEC028I) | | | A837 0300
+---------------------------------------+---------------------------------------+---------------------------------------| A837 1000
===== < CODE = 878 > ===== A878 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A878 0100
| THE ERROR OCCURED DURING,EXCUSION OF | * MORE VIRTUAL STORAGE WAS REQUESTED | * MAKE THE ENOUGH FREE SPACE. | A878 0200
| AN RC OR RU FORM GETMAIN MACRO INSTR- | THAN WAS AVAILABLE. | * EXTEND THE SPACE PARAMETER. | A878 0300
| UCTION. | * A NEGATIVE LENGTH WAS SPECIFIED. | | A878 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A878 1000
===== < CODE = 90A > ===== A90A 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A90A 0100
| INPUT TAPE DATA CHECK. | * HARD ERROR. | * SYMPLE RERUN. | A90A 0200
| | * INPUT,OUTPUT DD IS SPECIFIED DUMMY | | A90A 0300
| | ON USING VV1 UTILITY. | | A90A 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A90A 1000
===== < CODE = 913 > ===== A913 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ A913 0100
| INSUFFICIENT ACCESS AUTHORITY. | * READ THE FILE WHICH IS REGISTERED | * SPECIFY CORRECT USER ID AND PASS | A913 0200
| | TO RACF WITHOUT PASSWORD SPECIFICA- | WORD. | A913 0300
| | TION. | | A913 0400
+---------------------------------------+---------------------------------------+---------------------------------------| A913 1000
1 ************************************************************************************************************************* O 0000
* ON CONDITION CODE ( XXXX ) * O 0100
************************************************************************************************************************* O 0200
===== < CODE = 0021 > ===== O00210000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ O00210100
| RECORD VARIABLE SMALLER THAN RECORD | * DCB SPECIFICATION MISS. | * MAKING CORRECTION OF USER PGM. | O00210200
| SIZE. | THAT DCB WAS SPECIFIED BY THE DD | | O00210300
| | STATEMENT 'SORTOUT' OF PREVIOUS | | O00210400
| | STEP. | | O00210500
| | * DECLARE OF THE RECORD IN THE USER | * MAKING CORRECTION OF JCL. | O00210600
| | PROGRAM WAS INCORRECT. | | O00210700
| | | | O00210800
+---------------------------------------+---------------------------------------+---------------------------------------| O00211000
===== < CODE = 0022 > ===== O00220000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ O00220100
| RECORD VARIABLE LAGER THAN RECORD | LRECL (WHICH IS DCB SUBPARAMETER) | MAKING CORRECTION OF JCL. | O00220200
| SIZE. | SPECIFICATION MISS. | | O00220300
| | | | O00220400
+---------------------------------------+---------------------------------------+---------------------------------------| O00221000
===== < CODE = 0041 > ===== O00410000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ O00410100
| UNCORRECTABLE TRANSMISSION ERROR ON | ( UNKNOWN ) | RELOAD THE DATA BASE, AND RERUN THE | O00410200
| OUTPUT DATA SET. | | JOB. | O00410300
| | | | O00410400
+---------------------------------------+---------------------------------------+---------------------------------------| O00411000
===== < CODE = 0042 > ===== O00420000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ O00420100
| UNCORRECTABLE TRANSMISSION ERROR IN | * HARD I/O ERROR | * RERUN THE JOB. | O00420200
| INPUT DATA SET. | | (WHEN MSS TROUBLE, CHECK MSS I/O | O00420300
| | | ERROR.) | O00420400
| | * '0' RECORD FILE WAS NOT OPENED AND | * WHEN '0' RECORD FILE IS CREATED, | O00420500
| | CLOSED IN THE PREVIOUS STEP. | THAT FILE MUST BE OPENED. | O00420600
| | | | O00420700
+---------------------------------------+---------------------------------------+---------------------------------------| O00421000
===== < CODE = 0082 > ===== O00820000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ O00820100
| CONFLICT BETWEEN FILE ATTRIBUTES AND | AFTER DEFINE CLUSTER, THE RECORD | * WRITE THE 1ST RECORD BY UTILITY | O00820200
| PHISICAL ORGANIZATION OF DATA SET, | WAS WRITTEN DIRECTLY TO VSAM KSDS | ( REPRO OR JPD0VV1 ... ) . | O00820300
| E.G BETWEEN FILE ORGANIZATION AND | WITH ZERO RECORD. | * ADD NEXT LOGIC TO USER PGM. | O00820400
| DEVICE TYPE. | THE 1ST WRITING TO VSAM KSDS WITH | IF ONCODE=82 OCCURRED, | O00820500
| | ZERO RECORD MUST BE SEQUENTIAL WRITING| + OPEN THE VSAM KSDS WITH SEQUEN- | O00820600
| | . | TIAL, OUTPUT ATTRIBUTE BY TITLE | O00820700
| | | OPTION, AND | O00820800
| | | + WRITE HIGH VALUE RECORD, AND | O00820900
| | | + CLOSE THE FILE, | O00821000
| | | AND AFTER ABOVE ACTION, | O00821100
| | | PASS THE CONTROL THE TOP POSITION | O00821200
| | | OF PGM. | O00821300
| | | | O00821400
| | | USING TITLE OPTION, AMP='STRNO=1' | O00821500
| | | MUST BE SPECIFIED ON DD CARD. | O00821600
+---------------------------------------+---------------------------------------+---------------------------------------| O00821700
===== < CODE = 0083 > ===== O00830000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ O00830100
| AFTER MERGING ENVIRONMENT OPTIONS WITH| DIFFERENCE PGM DCB FROM JCL DCB | CORRECT JCL DCB | O00830200
|DD STATEMENT AND DATA SET LABEL, DATA | | | O00830300
|SET SPECIFICATION INCOMPLETE, | | | O00830400
| E.G. BLOCK SIZE OR RECORD FORMAT HAS | | | O00830500
|NOT BEEN SPECIFIED. | | | O00830600
+---------------------------------------+---------------------------------------+---------------------------------------| O00831000
===== < CODE = 0084 > ===== O00840000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ O00840100
| NO DD STATEMENT ASSOCIATING FILE WITH | * JCL WORK CORRECTION MISTAKE | * CORRECT JCL WORK ( SP30J ) | O00840200
|DATA SET | * NOT SPECIFIED DD STATEMENT | * ADD DD STATEMENT | O00840300
| | * INVALID DD STATEMENT SPECIFIED | * CORRECT DD STSTEMENT | O00840400
| | * INVALID FILE NAME SPECIFI D IN PGM | * CORRECT PGM | O00840500
+---------------------------------------+---------------------------------------+---------------------------------------| O00841000
===== < CODE = 0092 > ===== O00920000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ O00920100
| VSAM DATA SET OPEN ERROR | * NOT CLOSED THE VSAM DATA SET IN | * USE VERIFY COMMAND, AND CLOSE DATA | O00920200
| | LAST USE | SET | O00920300
| | * DATA SET SHARED WITH MULTI PROJECTS,| * USE VERIFY COMMAND CAREFULLY | O00920400
| | AFTER ONE IS ABEND AND NOT CLOSE IT, | ( MORE CAREFULLY WHEN ABEND DURING | O00920500
| | OTHER USE IT | UPDATING ) | O00920600
+---------------------------------------+---------------------------------------+---------------------------------------| O00921000
===== < CODE = 0310 > ===== O03100000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ O03100100
| FIXED OVERFLOW | * DURING CALCULATION | * CORRECT STATEMENT | O03100200
| | * COUNT AREA OVER | * INCREASE COUNT DATA FIELD | O03100300
+---------------------------------------+---------------------------------------+---------------------------------------| O03101000
===== < CODE = 0320 > ===== O03200000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ O03200100
| ZERO DIVIDE | * '0' VALUE DIVIDE | * '0' CHECK ( REVISE PGM ) | O03200200
| | * FIXED BIN OVERFLOW | * REVISE PGM ( PREVENT OVERFLOW ) | O03200300
| | * ADDITION CALCULATION BETWEEN BIN AND| * USE SAME ATTRIBUTE | O03200400
| | DEC | ( OCCURED IN '+' OR '*' OPERATION )| O03200500
+---------------------------------------+---------------------------------------+---------------------------------------| O03201000
1 ************************************************************************************************************************* U 0000
* USER ABEND CODE ( UXXXX ) * U 0100
************************************************************************************************************************* U 0200
===== < CODE = 0000 > ===== U00000000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00000100
| * I/O ERROR. | * SPECIFICATION ERROR OF SORT CONTROL | * MAKING CORRECTION OF SORT CTRL CARD.| U00000200
| | CARD. | | U00000300
| * SYNTAX ERROR. | * THE JOB EXECUTED NORMALLY UNDER | * CHANGE THE LENGTH OF THE SEGMENT NA-| U00000400
| | IMS/VS 1.1.3, BUT AFTER RELEASE UP, | ME FIELD IN UNQUALIFIED SSA FROM | U00000500
| ( THIS CODE CANNOT EXPLAIN THE | THAT JOB ABENDED UNDER IMS/VS 1.1.4. | 8 BYTE TO 9 BYTE. AND THEN 9TH BYTE | U00000600
| SPECIFIC ERROR ) | | MUST BE BLANK. | U00000700
| | | | U00000800
+---------------------------------------+---------------------------------------+---------------------------------------| U00001000
===== < CODE = 0002 > ===== U00020000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00020100
| THE JOB RUNNING UNDER RCS ABENDED. | THIS CODE WAS RETURED BY RCS. | | U00020200
| | PLEASE REFER SYSTEM CODE OR ON CODE. | | U00020300
| | | | U00020400
+---------------------------------------+---------------------------------------+---------------------------------------| U00021000
===== < CODE = 0005 > ===== U00050000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00050100
| RCS CONTROL TABLE CLEAR MISS. | THE JOB CONTROLLED BY RCS NORMALLY | * CLEAR THE RCS CONTROL TABLE , | U00050200
| | ENDED AT 1ST RUN, AND AGAIN THAT JOB | AND RERUN. | U00050300
| | STARTED AND NORMALLY ENDED. | * RESET PARAMETER. | U00050400
| | THEN, THE END CODE WAS SET ON CONTROL| | U00050500
| | TABLE. | | U00050600
| | | | U00050700
| | | | U00050800
| | | | U00050900
+---------------------------------------+---------------------------------------+---------------------------------------| U00051000
===== < CODE = 0007 > ===== U00070000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00070100
| INSUFFICIENT SPACE | AT MONTH END OPERATION, MANY JOBS | | U00070200
| | REQUIRED DASD SPACE ON THE SAME VOLUME| | U00070300
| | AT A ONCE TIME. | | U00070400
| | | | U00070500
| | | | U00070600
| | | | U00070700
| | | | U00070800
| | | | U00070900
+---------------------------------------+---------------------------------------+---------------------------------------| U00071000
===== < CODE = 0013 > ===== U00130000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00130100
| JOB=MS50IMSQ ABENDED. | BUFFER FULL BECAUSE OF BMP LOOP. | REEXECUTE THE JOB. | U00130200
| | | | U00130300
+---------------------------------------+---------------------------------------+---------------------------------------| U00131000
===== < CODE = 0016 > ===== U00160000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00160100
| * UNDEFINED FILE (ONCODE = 92) | * DD NAME MISSING | * CORRECT THE DD NAME | U00160200
| * ZERO DIVIDE (ONCODE = 320) | * ISAM SPACE INSUFFICIENT | * EXTEND THE SPACE OR BLOCKSIZE | U00160300
| * TAPE DATA CHECK | * ZERO DIVIDE | * ZERO CHECK MUST BE DONE AT DIVISION | U00160400
| * DATA EXCEPTION | * DECLARE STATEMENT OF USER PGM IS | * REGENERATE TAPE | U00160500
| * LENGTH OF RECORD VARIABLE GREATER | INCORRECT OR PHISICAL RECORD LENGTH | * REVISE THE DCL STATEMENT OR, | U00160600
| THAN RECORD LENGTH. | IS INCORRECT. | REVISE THE JCL PARAMETER OR, | U00160700
| | | REGENERATE DATA SET | U00160800
| | | | U00160900
+---------------------------------------+---------------------------------------+---------------------------------------| U00161000
===== < CODE = 0020 > ===== U00200000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00200100
| DUPLICATE KEY | KEY DUPLICATE OCCURRED DULING VSAM | REVISE THE USER PROGRAM WHICH OCCURR-| U00200200
| | LOAD WITH JPD0VV1. | ED DUPLICATE KEY. | U00200300
| | | | U00200400
+---------------------------------------+---------------------------------------+---------------------------------------| U00201000
===== < CODE = 0021 > ===== U00210000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00210100
| SYSTEM ISSUED RETURN CODE 21 . | IN ADDITION OF 'FEFE' RECORD TO VSAM | BOTH RECORD LENGTH SHOULD BE SAME. | U00210200
| | FILE, THE LENGTH OF 'FEFE' RECORD | | U00210300
| | (HIGH VALUE RECORD) LAGER THAN VSAM | | U00210400
| | RECORD LENGTH. | | U00210500
| | | | U00210600
+---------------------------------------+---------------------------------------+---------------------------------------| U00211000
===== < CODE = 0046 > ===== U00460000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00460100
| SORT CAPACITY EXCEEDED. | SORT WORK HAS INSUFFICIENT SPACE. | INCREASE THE SPACE, AND REEXECUTE | U00460200
| (SORT/MERGE) | | THE JOB. | U00460300
| | | | U00460400
+---------------------------------------+---------------------------------------+---------------------------------------| U00461000
===== < CODE = 0061 > ===== U00610000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00610100
| I/O ERROR. | HARD ERROR. | RE-INITIALIZE DASD. | U00610200
| | | | U00610300
+---------------------------------------+---------------------------------------+---------------------------------------| U00611000
===== < CODE = 0063 > ===== U00630000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00630100
| OPEN ERROR | BLKSIZE IN SECOND DD STMT IS LONGER | * REARRANGEMENT DD STATEMENTS IN ORDER| U00630200
| |THAN FIRST IN DD CONCATINATION | OF DECREASE OF BLKSIZE | U00630300
| | | * USE SAME BLKSIZE | U00630400
+---------------------------------------+---------------------------------------+---------------------------------------| U00631000
===== < CODE = 0066 > ===== U00660000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00660100
| SHORTAGE OF SPACE | SHORTAGE OF SORT WORK SPACE | INCREASE SPACE | U00660200
+---------------------------------------+---------------------------------------+---------------------------------------| U00661000
===== < CODE = 0068 > ===== U00680000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00680100
| OCCURED IN SORTD | * INVALID MERGE FIELD | * CORRECT MERGE FIELD | U00680200
| | * SEQUENCE ERROR IN ONE OF MERGED DATA| * CORRECT SEQUENCE | U00680300
| | SETS | | U00680400
+---------------------------------------+---------------------------------------+---------------------------------------| U00681000
===== < CODE = 0099 > ===== U00990000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U00990100
| | | RERUN | U00990200
+---------------------------------------+---------------------------------------+---------------------------------------| U00991000
===== < CODE = 0200 > ===== U02000000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U02000100
| CONTROL CHARACTER ERROR | NOT USED ASA CHARACTER | SET ASA CHARACTER | U02000200
| | ( ** ERROR CONTROL CHARACTER | | U02000300
| | SPECIFIED ** ) | | U02000400
+---------------------------------------+---------------------------------------+---------------------------------------| U02001000
===== < CODE = 0430 > ===== U04300000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U04300100
| BUFFER CONTROL ERROR | TOO LARGE BUFFER POOL SIZE | DECREASE BUFFER POOL SIZE | U04300200
| ( IMS/VS ) | | | U04300300
+---------------------------------------+---------------------------------------+---------------------------------------| U04301000
===== < CODE = 0476 > ===== U04760000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U04760100
| ABEND IN IMS BATCH REGION | TABLE OVER IN USER PROGRAM | INCREASE TABLE SIZE | U04760200
| ( IMS/VS ) | | | U04760300
+---------------------------------------+---------------------------------------+---------------------------------------| U04761000
===== < CODE = 0725 > ===== U07250000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U07250100
| S301 ABEND BECAUSE CSA ALLOCATION | NOT FREED CSA | RERUN AFTER RE-IPL | U07250200
|FAILED | | | U07250300
| ( IMS/VS ) | | | U07250400
+---------------------------------------+---------------------------------------+---------------------------------------| U07251000
===== < CODE = 0844 > ===== U08440000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U08440100
| ABEND IN IMS BATCH REGION | SHORTAGE OF OUTPUT SPACE | INCREASE SPACE | U08440200
| ( IMS/VS ) | | | U08440300
+---------------------------------------+---------------------------------------+---------------------------------------| U08441000
===== < CODE = 0852 > ===== U08520000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U08520100
| DASD CHECK | HARDWARE | RERUN | U08520200
+---------------------------------------+---------------------------------------+---------------------------------------| U08521000
===== < CODE = 0929 > ===== U09290000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ U09290100
| IMS/VS TERMINATED ABNORMALLY. | THE MEMBER WAS NOT FOUND IN THE DBD | * ADD THE MEMBER IN THE APPROPRIATE | U09290200
| | OR PSB LIBRARY. | LIBRARY. | U09290300
| | | * CONCATENATE OTHER PSB OR DBD LIB. | U09290400
| | | | U09290500
+---------------------------------------+---------------------------------------+---------------------------------------| U09291000
===== < CODE = 0612 > ===== 0612 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 0612 0100
| ERROR DURING CHARACTER STRING TO | * CONVERSION ERROR. | * | 0612 0200
| ARITHMETIC CONVERSION. | | | 0612 0300
| | | | 0612 0400
| | | | 0612 0500
| | | | 0612 0600
+---------------------------------------+---------------------------------------+---------------------------------------| 0612 1000
===== < CODE = 0853 > ===== 0853 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 0853 0100
| DLI/DB ROOT SEGMENT ACCESS TROUBLE. | * I/O ERROR OF DL/I DATA BASE. | * RELOAD OF DATA BASE. | 0853 0200
| (IMS/VS) | | | 0853 0300
| | | | 0853 0400
| | | | 0853 0500
| | | | 0853 0600
| | | | 0853 0700
| | | | 0853 0800
| | | | 0853 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 0853 1000
===== < CODE = 0990 > ===== 0990 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 0990 0100
| DFS2429I DBD OUT OF HIERARCHIC ABEND. | * INCORRECT ORDER OF SEGMENT IN DBD | * RE-EXCUTE OF PSBGEN. | 0990 0200
| (IMS/VS) | AND PSB. | | 0990 0300
| | | | 0990 0400
| | | | 0990 0500
| | | | 0990 0600
| | | | 0990 0700
| | | | 0990 0800
| | | | 0990 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 0990 1000
===== < CODE = 1000 > ===== 1000 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 1000 0100
| USER ABEND IN STANDARD MACRO. | | | 1000 0200
| | | | 1000 0300
| | | | 1000 0400
| | | | 1000 0500
| | | | 1000 0600
| | | | 1000 0700
| | | | 1000 0800
| | | | 1000 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 1000 1000
===== < CODE = 1029 > ===== 1092 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 1092 0100
| ATTEMPT TO REPOSITION IN VSAM DATA | * WHEN READ THE VSAM FILE WITH GENKEY,| * CREATE THE HIGHEST KEY VALUE RECORD | 1092 0200
| SET FAILED. | THE SPECIFIED KEY IS GREATER THAN | IN THE VSAM FILE. | 1092 0300
| | THE HIGHEST KEY OF THE VSAM FILE. | | 1092 0400
| | * WHEN READ DIRECT,ERROR OCCURED TOO. | | 1092 0500
| | | | 1092 0600
+---------------------------------------+---------------------------------------+---------------------------------------| 1092 1000
===== < CODE = 1111 > ===== 1111 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 1111 0100
| I/O ERROR. | | | 1111 0200
| | | | 1111 0300
| | | | 1111 0400
| | | | 1111 0500
| | | | 1111 0600
| | | | 1111 0700
| | | | 1111 0800
| | | | 1111 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 1111 1000
===== < CODE = 1428 > ===== 1428 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 1428 0100
| | | | 1428 0200
| (IMS/VS) | | | 1428 0300
| | | | 1428 0400
| | | | 1428 0500
| | | | 1428 0600
| | | | 1428 0700
| | | | 1428 0800
| | | | 1428 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 1428 1000
===== < CODE = 2004 > ===== 2004 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 2004 0100
| NAPS SPACE OVER. | | | 2004 0200
| | | | 2004 0300
| | | | 2004 0400
| | | | 2004 0500
| | | | 2004 0600
| | | | 2004 0700
| | | | 2004 0800
| | | | 2004 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 2004 1000
===== < CODE = 3001 > ===== 3001 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 3001 0100
| | | | 3001 0200
| | | | 3001 0300
| | | | 3001 0400
| | | | 3001 0500
| | | | 3001 0600
| | | | 3001 0700
| | | | 3001 0800
| | | | 3001 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 3001 1000
===== < CODE = 8091 > ===== 8091 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 8091 0100
| OPERATION EXCEPTION. | * SUBROUTINE IS NOT LINK-EDITTED. | * LINK OF SUBROUTINE. | 8091 0200
| ( AS SAME AS S0C1 ) | * SPECIFIED ENTRY POINT OF MODULE IS | * CORRECR ENTRY POINT. | 8091 0300
| | NOT RIGHT. | | 8091 0400
| | * INCORRECT VALUE IS SET IN THE LABEL | | 8091 0500
| | VALIABLE. | | 8091 0600
| | * DESTROY | | 8091 0700
| | | | 8091 0800
| | | | 8091 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 8091 1000
===== < CODE = 8094 > ===== 8094 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 8094 0100
| PROTECTION EXCEPTION. | | | 8094 0200
| | | | 8094 0300
| | | | 8094 0400
| | | | 8094 0500
| | | | 8094 0600
| | | | 8094 0700
| | | | 8094 0800
| | | | 8094 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 8094 1000
===== < CODE = 8097 > ===== 8097 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 8097 0100
| DATA EXCEPTION. | | | 8097 0200
| ( AS SAME AS S0C7 ) | | | 8097 0300
| | | | 8097 0400
| | | | 8097 0500
| | | | 8097 0600
| | | | 8097 0700
| | | | 8097 0800
| | | | 8097 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 8097 1000
===== < CODE = YYYY > ===== 9YYY 0000
+------------< EXPLANATION >------------+---------------< CAUSE >---------------+-------------< SOLUTION >--------------+ 9YYY 0100
| | | | 9YYY 0200
| | | | 9YYY 0300
| | | | 9YYY 0400
| | | | 9YYY 0500
| | | | 9YYY 0600
| | | | 9YYY 0700
| | | | 9YYY 0800
| | | | 9YYY 0900
+---------------------------------------+---------------------------------------+---------------------------------------| 9YYY 1000
浙公网安备 33010602011771号