LVS DR 负载均衡集群

LVS DR 负载均衡集群

试验准备：五台主机ABCDE，主机ABCDE均为单网卡，IP地址分别为192.168.10.2,192.168.10.3,192.168.10.4,192.168.10.5,192.168.10.6。主机A作为内网客户端，主机B负载均衡调度器，主机C和主机D作为网站服务器，主机E作为共享存储，均清除防火墙和SELINUX。操作系统均为RHELx86_64,为最小化安装。

主机A操作

#vim /etc/sysconfig/network-scripts/ifcfg-eth0

#service network restart

主机B操作

#vim /etc/sysconfig/network-scripts/ifcfg-eth0

#cp /etc/sysconfig/network-scripts/ifcfg-eth0 /etc/sysconfig/network-scripts/ifcfg-eth0:0

#service network restart

#vim /etc/sysctl.conf

net.ipv4.conf.all.send_redirects=0

net.ipv4.conf.default.send_redirects=0

net.ipv4.conf.eth0.send_redirects=0

#sysctl –p

#modprobe ip_vs

#cat /proc/net/ip_vs

#cd /mnt/cdrom/Packets

#rpm –ivh ipvsadm-1.25-10.el6.x86_64.rpm

#service ipvsadm stop #这个命令会清除原来设定的规则

#ipvsadm –A –t 192.168.10.10:80 –s rr

#ipvsadm –a –t 192.168.10.10:80 –r 192.168.10.4:80 –g

#ipvsadm –a –t 192.168.10.10:80 –r 192.168.10.5:80 –g

#service ipvsadm save

主机E操作

#vim /etc/sysconfig/network-scripts/ifcfg-eth0

#service network restart

#rpm –qa | grep nfs

#vim /etc/exports

#mkdir /share

#cd /share

#vim index.html

www.taobao.com

#service rpcbind start

注：RHEL6之后，portmap的启动方式改了，必须启动，否则nfs会报错

#servie nfs start

#chkconfig rpcbind on

#chkcofig nfs on

#yum -y install showmount #安装showmount命令

#showmount –e 192.168.10.6

#exportfs –rv

主机C操作

#yum –y install httpd

#service httpd start

#chkconfig httpd on

#yum –y install showmount

#showmount –e 192.168.10.6

#mount 192.168.10.6:/share /var/www/html

#curl 192.168.10.4

#vim /etc/sysconfig/network-scripts/ifcfg-eth0

#cp /etc/sysconfig/network-scripts/ifcfg-lo /etc/sysconfig/network-scripts/ifcfg-lo:0

#vim /etc/sysconfig/network-scripts/ifcfg-lo:0

#vim /etc/sysctl.conf

net.ipv4.conf.all.arp_ignore=1

net.ipv4.conf.all.arp_announce=2

net.ipv4.conf.default.arp_ignore=1

net.ipv4.conf.default.arp_announce=2

net.ipv4.conf.lo.arp_ignore=1

net.ipv4.conf.lo.arp_announce=2

#route add –host 192.168.10.10 dev lo:0

#vim /etc/rc.d/rc.local

/sbin/route add –host 192.168.10.10 dev lo:0

主机D操作

#yum –y install httpd

#service httpd start

#chkconfig httpd on

#yum –y install showmount

#showmount –e 192.168.10.6

#vim /var/www/html/index.html #为了便于下面的测试，所以用不同网页

www.baidu.com

#vim /etc/sysconfig/network-scripts/ifcfg-eth0

#cp /etc/sysconfig/network-scripts/ifcfg-lo /etc/sysconfig/network-scripts/ifcfg-lo:0

#vim /etc/sysconfig/network-scripts/ifcfg-lo:0

#vim /etc/sysctl.conf

net.ipv4.conf.all.arp_ignore=1

net.ipv4.conf.all.arp_announce=2

net.ipv4.conf.default.arp_ignore=1

net.ipv4.conf.default.arp_announce=2

net.ipv4.conf.lo.arp_ignore=1

net.ipv4.conf.lo.arp_announce=2

#route add –host 192.168.10.10 dev lo:0

#vim /etc/rc.d/rc.local

/sbin/route add –host 192.168.10.10 dev lo:0

#ipvsadm –Ln

主机B操作：

测试

在浏览器输入curl 192.168.10.10

可以知道主机C和主机D交互出现。

LVS+keeplived实现服务器的高可用

keepalived概述
为LVS和HA设计的一款健康状态工具；
支持故障自动切换（Failover）；
支持节点健康状态检查（Health Checking）；
keepalived的热备方式
VRRP（Virtual Router Redundancy Protocol，虚拟路由冗余协议）--主+多备，共用同一个IP地址，但优先级不同。
lvs+keepalived
负载均衡+高可用集群，针对Lvs调度器实现双机热备，能够管理服务器池，自动隔离失效节点

4．实现LVS+keepalived实现高可用集群

试验在上面试验的基础上，在加上一台服务器作为从调度器，IP地址为192.168.10.7