华为交换机查看接口所有默认配置

接口下 display this 可以看到当前配置

但看不到默认配置，因为默认不显示。

查看命令 display this include-default

[huawei8865-25GE1/4/2]dis this include-default 
#
interface 25GE1/4/2
 ~undo shutdown
 ~enable snmp trap updown
 ~trap-threshold input-rate 90 resume-rate 90
 ~trap-threshold output-rate 90 resume-rate 90
 ~qinq protocol 8100
 ~port link-type access
 ~port default vlan 1
 ~undo port discard tagged-packet
 ~undo port bridge enable
 ~undo mac-vlan enable
 ~vlan precedence mac-vlan
 ~undo ip-subnet-vlan enable
 ~undo port-isolate enable
 ~undo loop-protect l2-subinterface enable
 ~stp enable
 ~undo stp config-digest-snoop
 ~undo stp no-agreement-check
 ~undo stp loop-protection
 ~undo stp root-protection
 ~stp point-to-point auto
 ~stp compliance auto
 ~stp instance 0 port priority 128
 ~undo stp tc-restriction enable
 ~undo bpdu bridge enable
 ~mac-address limit maximum 0
 ~storm suppression broadcast 10
 ~storm suppression multicast 100
 ~storm suppression unknown-unicast 100
 ~arp anti-attack rate-limit 0
 ~undo mac-address learning disable
 ~mac-address learning priority 0
 ~undo port-security enable
 ~undo lldp disable
 ~lldp admin-status txrx
 ~undo lldp tlv-disable basic-tlv all
 ~undo lldp tlv-disable dot1-tlv port-vlan-id
 ~undo lldp tlv-disable dot1-tlv protocol-vlan-id
 ~undo lldp tlv-disable dot1-tlv vlan-name
 ~undo lldp tlv-enable dot1-tlv protocol-identity
 ~undo lldp tlv-disable dot3-tlv all
 ~undo identity enable
 ~undo smart-link flush receive
 ~trust upstream default
 ~trust 8021p outer
 ~port priority 0
 ~undo qos phb marking 8021p disable
 ~qos pq 0 to 7
 ~undo dhcp snooping alarm dhcpv6-rate enable
 ~dhcp snooping alarm dhcpv6-rate threshold 100
 ~undo dhcp snooping alarm dhcpv6-request enable
 ~undo dhcp snooping check dhcpv6-rate enable
 ~dhcp snooping check dhcpv6-rate 5000
 ~undo dhcp snooping check dhcpv6-request mac
 ~undo dhcp snooping alarm dhcpv6-reply enable
 ~undo dhcpv6 snooping check relay-forward enable
 ~undo dhcpv6 option18 insert enable
 ~undo dhcpv6 option18 rebuild enable
 ~undo dhcpv6 option37 insert enable
 ~undo dhcpv6 option37 rebuild enable
 ~undo nd snooping enable
 ~undo nd snooping trusted
 ~undo nd snooping check na enable
 ~undo nd snooping check ns enable
 ~undo nd snooping check rs enable
 ~undo nd snooping alarm binding-table check enable
 ~undo nd snooping check dad-ns retransmit-rate enable
 ~nd snooping check dad-ns retransmit-rate rate 50
 ~nd snooping max-user-number 9216
 ~savi max-binding-table 9216
 ~storm control interval 5
 ~undo dhcp anti-attack check magic-cookie
 ~dhcp anti-attack check udp-checksum
 ~undo dhcp option82 insert enable
 ~undo dhcp option82 rebuild enable
 ~undo dhcp option82 append vendor-specific
 ~dhcp option82 format default
 ~undo dhcp option82 encapsulation
 ~undo dhcp snooping enable
 ~undo dhcp snooping disable
 ~undo dhcp snooping enable no-user-binding
 ~undo dhcp snooping trusted
 ~undo dhcp snooping check dhcp-giaddr enable
 ~undo dhcp snooping check dhcp-request enable
 ~undo dhcp snooping check dhcp-chaddr enable
 ~undo dhcp snooping alarm dhcp-chaddr enable
 ~undo dhcp snooping alarm dhcp-reply enable
 ~undo dhcp snooping alarm dhcp-request enable
 ~undo dhcp snooping check dhcp-rate enable
 ~undo dhcp snooping alarm dhcp-rate enable
 ~dhcp snooping check dhcp-rate 5000
 ~dhcp snooping alarm dhcp-rate threshold 100
 ~dhcp snooping user-bind max-number 9216
 ~stp vlan 1 to 4094 port priority 128 
 ~port pfc-deadlock trigger turn-off
 ~ifg 12
 ~set flow-change-ratio input-threshold upper-limit 50
 ~set flow-change-ratio output-threshold upper-limit 50
 ~set flow-change-ratio interval 5
 ~set flow-change-ratio start-check bandwidth-usage 20
 ~port link-flap interval 10
 ~port link-flap threshold 5
 ~carrier down-hold-time 0
 ~carrier up-hold-time 0
 ~jumboframe enable 9216
 ~trap-threshold crc-statistics 3 interval 10 repeat-time 1
 ~set flow-statistics include-interframe
 ~set up-delay 0
#
return