CCNA学习笔记24--RIPv1实验(实验）

实验目的：学习RIPv1的实验配置
实验拓扑：

实验配置：
1.基本配置
Router>enable
Router#configure terminal
Router(config)#enable password cisco
Router(config)#no ip domain lookup
Router(config)#line console 0
Router(config-line)#password cisco
Router(config-line)#logging synchronous
Router(config-line)#exec-timeout 0 0
Router(config-line)#exit
Router(config)#line vty 0 4
Router(config-line)#password cisco
Router(config-line)#logging synchronous
Router(config-line)#exit
Router(config)#hostname R1
R1(config)#^Z
R1#wr
Building configuration...
[OK]
2.端口配置对应IP
R1(config)#interface loopback 0
R1(config-if)#ip address 11.1.1.1 255.255.255.0
R1(config-if)#no shutdown
R1(config)#interface ethernet 0/0
R1(config-if)#ip address 12.1.1.1 255.255.255.0
R1(config-if)#no shutdown
R1#show ip interface brief
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0/0                12.1.1.1        YES manual up                    up     
Ethernet0/1                unassigned      YES unset  administratively down down   
Ethernet0/2                unassigned      YES unset  administratively down down   
Ethernet0/3                unassigned      YES unset  administratively down down   
Loopback0                  11.1.1.1        YES manual up                    up     
3.配置RIPv1
R1(config)#router rip       //起RIP进程
R1(config-router)#version 1       //运行版本1
R1(config-router)#network 11.0.0.0       //宣告loopback0进入RIP进程，RIP都用的是主类宣告的方式。
R1(config-router)#network 12.0.0.0    //宣告ethernet 0/0 进入RIP进程

R2(config)#router rip
R2(config-router)#version 1
R2(config-router)#network 22.0.0.0
R2(config-router)#network 12.0.0.0
R2(config-router)#network 23.0.0.0

R3(config)#router rip
R3(config-router)#version 1
R3(config-router)#network 33.0.0.0
R3(config-router)#network 23.0.0.0
4.检查
R1#show ip route
      11.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C        11.1.1.0/24 is directly connected, Loopback0
L        11.1.1.1/32 is directly connected, Loopback0
      12.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C        12.1.1.0/24 is directly connected, Ethernet0/0
L        12.1.1.1/32 is directly connected, Ethernet0/0
R     22.0.0.0/8 [120/1] via 12.1.1.2, 00:00:18, Ethernet0/0
R     23.0.0.0/8 [120/1] via 12.1.1.2, 00:00:18, Ethernet0/0
R     33.0.0.0/8 [120/2] via 12.1.1.2, 00:00:18, Ethernet0/0

R1#ping 33.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 33.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms