【DM8168学习笔记4】ezsdk安装过程记录
安装文件 ezsdk_dm816x-evm_5_05_02_00_setuplinux
DM8168-EZSDK文件结构如图所示。
运行ezsdk/setup.sh，继续安装配置：
安装配置工具软件包（tftp服务器，nfs服务器，minicom串口工具，uboot和内核编译工具）
可参考：http://www.61ic.com/Article/DaVinci/TMS320DM81x/201112/39896.html
编译SDK，安装编译后组件在$HOME/tarfetfs目录下。
编译SDK，安装编译后组件在$HOME/tarfetfs目录下。
默认安装情况下：
1.在主机用tftp来引导linux内核，linux内核默认在/tftpboot目录下提取；
2.在主机用nfs来引导linux文件系统，文件系统默认安装在$HOME/targetfs目录下；
3.Minicom设置成和USB-UART（J6）通信。
以下是中终端显示的过程：
eagle@eagle-desktop:~$ sudo '/usr/local/ezsdk/setup.sh' [sudo] password for eagle: -------------------------------------------------------------------------------- TISDK setup script This script will set up your development host for sdkdevelopment. Parts of this script require administrator priviliges (sudoaccess). -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Verifying Linux host distribution Ubuntu 10.04 LTS found successfully, continuing.. -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will make sure you have the proper host supportpackages installed using the following command: sudoapt-get install xinetd tftpd nfs-kernel-serverminicom build-essential libncurses5-devuboot-mkimage autoconf automake Note! This command requires you to have administratorpriviliges (sudo access) on your host. Press return to continue 正在读取软件包列表... 完成 正在分析软件包的依赖关系树 正在读取状态信息... 完成 xinetd 已经是最新的版本了。 tftpd 已经是最新的版本了。 nfs-kernel-server 已经是最新的版本了。 minicom 已经是最新的版本了。 build-essential 已经是最新的版本了。 libncurses5-dev 已经是最新的版本了。 uboot-mkimage 已经是最新的版本了。 autoconf 已经是最新的版本了。 automake 已经是最新的版本了。 automake 被设置为手动安装。 升级了 0 个软件包，新安装了 0 个软件包，要卸载 0 个软件包，有 223 个软件包未被升级。 Package verification and installation successfullycompleted -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- In which directory do you want to install the targetfilesystem?(if this directory does not exist it will becreated) Ensure that complete path is provided, otherwise NFS path inbootargs might be incomplete [ /home/eagle/targetfs ] -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will extract the target filesystem to/home/eagle/targetfs #根文件系统的路径：/home/eagle/targetfs Note! This command requires you to have administratorpriviliges (sudo access) on your host. Press return to continue /home/eagle/targetfs already exists (r) rename existing filesystem (o) overwrite existingfilesystem (s) skip filesystem extraction [r] o Old /home/eagle/targetfs removed Successfully extracted ezsdk-dm816x-evm-rootfs.tar.gz to/home/eagle/targetfs -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will update the EXEC_DIR variables in the Rules.make file This will facilitate the SDK to install (with make install)rebuilt binaries in /home/eagle/targetfs/home/root/dm816x-evm The files will be available from /home/root/dm816x-evm on thetarget. This setting can be changed later by editing Rules.make andchanging the EXEC_DIR variable. Press return to continueRules.make edited successfully.. -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will export your target filesystem for NFSaccess. Note! This command requires you to have administratorpriviliges (sudo access) on your host. Press return to continue * Stopping NFS kernel daemon [ OK ] * Unexporting directories for NFS kerneldaemon... [ OK ] * Exporting directories for NFS kerneldaemon... [ OK] * Starting NFS kernel daemon [ OK ] -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Which directory do you want to be your tftp root directory?(if this directory does notexist it will be created for you) [ /tftpboot] -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will set up the tftp server in the /tftpbootdirectory. Note! This command requires you to have administratorpriviliges (sudo access) on your host. Press return to continue Successfully copied uImage-dm816x-evm.bin to tftp root directory/tftpboot #编译好的内核镜像文件路径：/tftpboot /etc/xinetd.d/tftp successfullycreated Restarting tftp server * Stopping internet superserver xinetd [ OK ] * Starting internet superserver xinetd [ OK ] -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will set up minicom (serial communicationapplication) for SDK development For boards that contain a USB-to-Serial converter on the board(BeagleBone), the port used for minicom will be automatically detected. Bydefault Ubuntu will not recognize this device. Setup will add will add a udevrule to /etc/udev/ so that from now on it will be recognized as soonas the board is plugged in. For other boards, the serial will defualt to /dev/ttyS0.Please update based on your setup. -------------------------------------------------------------------------------- NOTE: For boards with a built-in USB to Serial adapter pleasepress ENTERat the prompt below. The correct port will bedetermined automatically at a later step. For all otherboards select theserial port that the board is connected to Which serial port do you want to use with minicom? [ /dev/ttyS0] Configuration saved to /home/eagle/.minirc.dfl. You can changeit further from inside minicom, see the Software Development Guide for moreinformation. -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will set up the u-boot variables for booting theEVM. Autodetected the following ip address of your host, correct itif necessary [ ] Select Linux kernel location: 1: TFTP 2: SD card [ 1 ] Select root file system location: 1: NFS 2: SD card [ 1 ] Available kernel images in /tftproot: uImage-dm816x-evm.bin Which kernel image do you want to boot from TFTP? [ uImage-dm816x-evm.bin] Resulting u-boot variable settings: setenv bootdelay 4 setenv baudrate 115200 setenv bootargs console=ttyO2,115200n8 rootwait rwmem=364M@0x80000000 mem=320M@0x9FC00000 vmalloc=500Mnotifyk.vpssm3_sva=0xBF900000 root=/dev/nfsnfsroot=:/home/eagle/targetfs ip=dhcp setenv bootcmd 'dhcp;setenv serverip ;tftpboot;bootm' setenv autoload no setenv serverip setenv bootfile uImage-dm816x-evm.bin -------------------------------------------------------------------------------- Would you like to create a minicom script with the aboveparameters (y/n)? [ y ] Successfully wrote setup_uimage-tftp_fs-nfs.minicom Would you like to run the setup script now (y/n)? Thisrequires you to connect the RS-232 cable between your host and EVM as well as yourethernet cable as described in the Quick Start Guide. Please ensure that SW4switch for NAND is in ON position. Once answering 'y' on the prompt below you will have 300seconds to connect the board and power cycle it before the setup times out After successfully executing this script, your EVM will be setup. You will be able to connect to it by executing 'minicom -w' or if youprefer a windows host you can set up Tera Term as explained in the SoftwareDeveloper's Guide. If you connect minicom or Tera Term and power cycle the boardLinux will boot. [ y ] /usr/local/ezsdk ~ Welcome to minicom 2.4 OPTIONS: I18n Compiled on Jan 25 2010, 06:49:09. Port /dev/ttyS0 Press CTRL-A Z for help on special keys CTRL-A Z for help |115200 8N1 | NOR |Minicom 2.4 | VT102 | Online00:14 You can manually run minicom in the future with this setupscript using: minicom -S setup_uimage-tftp_fs-nfs.minicom -------------------------------------------------------------------------------- TISDK setup completed! Please continue reading the Software Developer's Guide formore information on how to develop software on the EVM
eaglediao
