开机自启动nginx,php-fpm

 

开机自启动nginx,php-fpm(其他服务类似)

centos 7以上是用Systemd进行系统初始化的,Systemd 是 Linux 系统中最新的初始化系统(init),它主要的设计目标是克服 sysvinit 固有的缺点,提高系统的启动速度。 Systemd服务文件以.service结尾,比如现在要建立nginx为开机启动,如果用yum install命令安装的,yum命令会自动创建nginx.service文件,直接用命令systemcel enable nginx.service设置开机启动即可。

systemcel enable nginx.service

源码安装的手动建立nginx.service服务文件

  1. 在系统服务目录里创建nginx.service文件
    vi /lib/systemd/system/nginx.service
    写入以下内容(路径改成自己的)
    [Unit]
    Description=nginx
    After=network.target
    [Service]
    Type=forking
    ExecStart=/www/lnmp/nginx/sbin/nginx -c /www/lnmp/nginx/conf/nginx.conf
    ExecReload=/www/lnmp/nginx/sbin/nginx -s reload
    ExecStop=/www/lnmp/nginx/sbin/nginx -s quit
    PrivateTmp=true
    [Install]
    WantedBy=multi-user.target

     

    在系统服务目录里创建php-fpm.service文件
    vi /lib/systemd/system/php-fpm.service
    写入以下内容(路径改成自己的)
    [Unit]
    Description=php-fpm
    After=network.target
    [Service]
    Type=forking
    ExecStart=/www/lnmp/php/sbin/php-fpm
    PrivateTmp=true
    [Install]
    WantedBy=multi-user.target

     

    [Unit]:服务的说明
    Description:描述服务
    After:描述服务类别
    [Service]服务运行参数的设置
    Type=forking是后台运行的形式
    ExecStart为服务的具体运行命令
    ExecReload为重启命令
    ExecStop为停止命令
    PrivateTmp=True表示给服务分配独立的临时空间
    注意:[Service]的启动、重启、停止命令全部要求使用绝对路径
    [Install]运行级别下服务安装的相关设置,可设置为多用户,即系统运行级别为3

  2. 测试并加入开机自启
    先关闭nginx,php-fpm
    使用以下命令开启
    systemctl start nginx.service             #如果服务是开启状态,使用此命令会启动失败。
    systemctl start php-fpm.service

     

    开启成功,将服务加入开机自启
    systemctl enable nginx.service                #注意后面不能跟空格
    systemctl enable php-fpm.service

     

    重启服务器,查看是否启动
    shutdown -r now        #重启
    systemctl list-units --type=service           #查看运行的服务

     




其他命令
systemctl start nginx.service              #启动nginx服务
systemctl enable nginx.service             #设置开机自启动
systemctl disable nginx.service            #停止开机自启动
systemctl status nginx.service             #查看服务当前状态
systemctl restart nginx.service           #重新启动服务
systemctl list-units --type=service        #查看所有已启动的服务

 



转载:https://blog.csdn.net/ijijni/article/details/78513521
posted @ 2018-04-14 11:38  水飝飞天  阅读(274)  评论(0编辑  收藏  举报