基于51单片机+DAC0832的信号发生器

最近帮别人设计一个毕业设计,做一个多种信号发生器(四种波形:方波、三角波、锯齿波、梯形波),现在贴上来给大家参考,如果有错误的地方,望指出~

下面先贴上仿真的电路图(仿真的软件是Protuse,上传一个大点的图,方便大家看的清楚点):

原件清单:STC89C52单片机X1、DAC0832转换器X1、12M晶振X1、电容22pfX2、10uf的电容X1、1nf陶瓷电容X1、独立按键X4、10千欧排阻X1、10KΩ电阻X5、LM358                 单电源运放X1。仿真就需要这些原件,具体的硬件设计大家定好了在制作~

下面上传一下C程序吧~(使用的IDE环境是Keil 4,语言是C语言)

Source文件(.c文件):

1\main.c文件:

 1 #include "reg52.h"
 2 #include "init.h"
 3 #include "single.h"
 4 #include "delay.h"
 5 #include "Key.h"
 6 int main(void)
 7 {
 8     unsigned char Model=0;//0-方波 1-三角波 2-锯齿波 3-正弦波
 9     unsigned int Count=0;//计数器
10     unsigned int Squ_Per=256;
11     unsigned int Tri_Per=256;
12     unsigned int Saw_Per=256;
13     unsigned int Sin_Per=256;
14     init();
15     while(1)
16     {
17         while(Model==0)
18         {    
19             Square_wave(Squ_Per,&Count);
20             Count+=4;
21             Squ_Per=Key_Plus(Squ_Per);
22             Squ_Per=Key_Subc(Squ_Per);
23             Model=Key_Model(Model,&Squ_Per,&Count);//每次退出当前while时记得复原Period和Count的数据
24         }    
25         while(Model==1)
26         {
27             Triangle_wave(Tri_Per,&Count);
28             Count+=4;
29             Tri_Per=Key_Plus(Tri_Per);
30             Tri_Per=Key_Subc(Tri_Per);
31             Model=Key_Model(Model,&Tri_Per,&Count);
32         }
33         while(Model==2)
34         {
35             Sawtooth_wave(Saw_Per,&Count);
36             Count+=4;
37             Saw_Per=Key_Plus(Saw_Per);
38             Saw_Per=Key_Subc(Saw_Per);
39             Model=Key_Model(Model,&Saw_Per,&Count);
40         }
41         while(Model==3)
42         {
43             Sin_wave(Sin_Per,&Count);
44             Count+=4;
45             Sin_Per=Key_Plus(Sin_Per);
46             Sin_Per=Key_Subc(Sin_Per);
47             Model=Key_Model(Model,&Sin_Per,&Count);
48         }
49     }
50      return 0;
51 }

2\init.c文件:

 1 #include "reg52.h"
 2 sbit CS_DAC=P1^5;//DAC0832的片选端口
 3 sbit WR_DAC=P1^6;//DAC0832的数据写入端口
 4 extern void init(void)
 5 {
 6     P0=0xff;
 7     P1=0xff;
 8     P2=0xff;
 9     P3=0xff;
10     CS_DAC=0;//一直片选中DAC0832,低电平有效啊~
11     WR_DAC=0;//一直写入数据到DAC0832
12 }

3\single.c文件

 1 #include "reg52.h"
 2 #include "single.h"
 3 #include "delay.h"
 4 #define DATA P0
 5 void Square_wave(unsigned int Per,unsigned int *Count)
 6 {
 7     if(*Count>=Per) *Count=0;
 8     if(*Count<Per/2)
 9     {
10         DATA=0x00;
11     }    
12     else
13     {
14         DATA=0xFF;
15     }
16 }
17 void Triangle_wave(unsigned int Per,unsigned int *Count)
18 {
19     if(*Count>=Per) *Count=0;
20     if(*Count<Per/2)
21     {
22         DATA=*Count;
23     }    
24     else
25     {
26         DATA=Per-*Count;
27     }    
28 }
29 void Sawtooth_wave(unsigned int Per,unsigned int *Count)
30 {
31     if(*Count>=Per) *Count=0;
32     if(*Count<Per)
33     {
34         DATA=*Count;
35     }        
36 }
37 void Sin_wave(unsigned int Per,unsigned int *Count)
38 {
39     if(*Count>Per) *Count=0;
40     if(*Count<Per/2)
41     {
42         DATA=*Count;
43     }    
44     else if(*Count==Per/2)
45     {
46         delay(100);    
47     }
48     else if(*Count<Per)
49     {
50         DATA=Per-*Count;
51     }    
52     else if(*Count==Per)
53     {
54         delay(100);
55     }
56 }

4\Key.c文件:

 1 #include "Key.h"
 2 #include "delay.h"
 3 sbit key2=P3^3;    //wave Change
 4 sbit key3=P3^4;    //Fre plus
 5 sbit key4=P3^5;    //Fre subc
 6 unsigned char Key_Model(unsigned char Model,unsigned int *Pre,unsigned int *Count)
 7 {
 8     if(key2==0)
 9     {
10         delay(10);
11         if(key2==0)
12         {
13             Model=Model+1;
14             *Pre=256;
15             *Count=0;    
16         }
17     }
18     while(key2==0);
19     if(Model>3)
20     {
21         Model=0;
22     }
23     return Model;
24 }
25 unsigned int Key_Plus(unsigned int Per)
26 {
27     if(key3==0)
28     {
29         delay(10);
30         if(key3==0)
31         {
32             Per=Per+8;    
33         }
34     }
35     while(key3==0);
36     if(Per>256)
37     {
38         Per=0;
39     }
40     return Per;        
41 }
42 unsigned int Key_Subc(unsigned int Per)
43 {
44     if(key4==0)
45     {
46         delay(10);
47         if(key4==0)
48         {
49             Per=Per-8;    
50         }
51     }
52     while(key4==0);
53     if(Per<0)
54     {
55         Per=256;
56     }
57     return Per;        
58 }

5\delay.c文件:

1 void delay(unsigned int r)
2 {
3  unsigned int i,j;
4  for(i=r;i>0;i--)
5   for(j=110;j>0;j--);
6 }

Header文件(.h文件):

1\init.h文件:

1 extern void init(void);

2\single.h文件:

1 void Square_wave(unsigned int Per,unsigned int *Count);
2 void Triangle_wave(unsigned int Per,unsigned int *Count);
3 void Sawtooth_wave(unsigned int Per,unsigned int *Count);
4 void Sin_wave(unsigned int Per,unsigned int *Count);

3\Key.h文件:

1 #include "reg52.h"
2 unsigned char Key_Model(unsigned char Model,unsigned int *Pre,unsigned int *Count);
3 unsigned int Key_Plus(unsigned int Per);
4 unsigned int Key_Subc(unsigned int Per);

4\delay.h文件:

1 #include <intrins.h>
2 void delay(unsigned int r);
3 #define NOP() _nop_()

所用的工程文件我都已经上传喽~,下面来看看仿真的结果:(大家在电路设计的时候可以进行一下滤波处理,然后对信号进行放大处理,这样的话效果可能会更好点哦~)

                 方波:                                        三角波:                                           锯齿波:                                   梯形波:

大家转载请注明出处!谢谢!

在这里要感谢GISPALAB实验室的各位老师和学长学姐的帮助!谢谢~

 

大家注意下,电路有个小问题,由于本人的失误,DAC0832的Iout1和Iout2的输出接口的接法应该按如下的接入方式:

需要修改的地方有:

1、电源改成双电源

2、Iout接口需要接地

修改完毕之后的结果就会比较完美了,下面上传一个三角波的波形

posted @ 2016-05-25 22:45  小淼博客  阅读(16658)  评论(3编辑  收藏  举报

大家转载请注明出处!谢谢! 在这里要感谢GISPALAB实验室的各位老师和学长学姐的帮助!谢谢~