TPFanControl.ini

64位系统安装目录分为两种
64位用：C:\Program Files
32位用：C:\Program Files (x86)
64位系统系统目录分为两种
64位用：C:\Windows\System32
32位用：C:\Windows\SysWOW64
64位系统注册表分为两种
64位用：[HKEY_LOCAL_MACHINE\SOFTWARE]
32位用：[HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node]

所以在64位系统中运行32位的DLL，应将DLL放在C:\Windows\SysWOW64目录下，写注册表应该是[HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node]下，调用的程序应该在C:\Program Files (x86)下。注册表中的键值应该指向的是C:\Windows\SysWOW64下

> dumpbin /headers tvicport.dll
Microsoft (R) COFF/PE Dumper Version 14.13.26131.1
Copyright (C) Microsoft Corporation.  All rights reserved.


Dump of file tvicport.dll

PE signature found

File Type: DLL

FILE HEADER VALUES
             14C machine (x86)
               5 number of sections
        424A6D4E time date stamp Wed Mar 30 17:11:42 2005
               0 file pointer to symbol table
               0 number of symbols
              E0 size of optional header
            210E characteristics
                   Executable
                   Line numbers stripped
                   Symbols stripped
                   32 bit word machine
                   DLL
......


> dumpbin /headers tvicport.sys
Microsoft (R) COFF/PE Dumper Version 14.13.26131.1
Copyright (C) Microsoft Corporation.  All rights reserved.


Dump of file tvicport.sys

PE signature found

File Type: EXECUTABLE IMAGE

FILE HEADER VALUES
             14C machine (x86)
               8 number of sections
        424A6D84 time date stamp Wed Mar 30 17:12:36 2005
               0 file pointer to symbol table
               0 number of symbols
              E0 size of optional header
             30E characteristics
                   Executable
                   Line numbers stripped
                   Symbols stripped
                   32 bit word machine
                   Debug information stripped
......

!)Green.bat

@copy TVicPort.sys %WINDIR%\SysWOW64\drivers /y
@copy TVicPort64.sys %WINDIR%\System32\drivers /y
@copy TVicPort.dll %WINDIR%\System /y

killtpfc.bat

TASKKILL /F /IM tpfcicon.exe
TASKKILL /F /IM tpfcicon_noballons.exe
TASKKILL /F /IM TPFanControl.exe
net stop TPFanControl
TPFanControl -u

TPFanControl.ini

//NEW: Set UseTWR=1 to see more sensors, will work only on newer T4xx
// ATTENTION: if only one (cpu) sensor is displayed, TWR is not 
// working properly, displayed temp is faulty, go back to UseTWR=0
// 新：设置usetwr=1以查看更多传感器，仅适用于较新的t4xx
// 注意：如果只显示一个（CPU）传感器，则twr不显示
// 工作正常，显示温度有问题，返回使用twr=0

// Notice: Only Support TPFC v0.63 Setting
UseTWR=0

//--------------------------------------------------------------------
//
// >>>>  Celsius / Fahrenheit: temperatures in degree Celsius(active) / Fahrenheit  <<<<

// !!!! "Level" FAN 0 > 80 -> switch to Fahrenheit !!!! see below
// 最低一级的温度值如果>80的话,则温度自动识别为华氏度.

// ATTENTION: example temp values are for my T61, especially
// BluetoothEDR=1,  SensorName5=no5, IgnoreSensors=no5 too 
// temp levels 10 degrees centgrade higher than in T4x, R5x,
// change for your purposes.
// 注意,下面的温度设置是以我的T61为例,特别是蓝牙EDR设置为1,第五个传感器名称改为no5,并且忽略这个传感器的温度显示.在T4X,R5X机器上,温度设置要高个10°,总之以你自己实测的效果来调试.


// advice for programmers: TPFanControl must acquire mutex named
// "Access_Thinkpad_EC" to get access to embedded controller
// 建议: TPFanControl必须获得"Access_Thinkpad_EC"才能得到温度值.

// with Active=3 & ManFanSpeed=0 & ManModeExit=78 you can have a nice
// quiet time until temps reaches 78 deg. centigrade  :-))
// 当使用手动模式(Active=3),风速为0(ManFanSpeed=0),并且将"手动切换到智能的温度阀值"设定为78°(ManModeExit=78)的话,你的电脑将会异常安静,除非温度攀升到78°.

// -----------------------------------------------------------------
// -----------------------------------------------------------------
// "Active=0" program just reads config.  程序仅读取配置
// "Active=1" allow program to modify fan.  允许程序修改风速
// "Active=2" program will come up in smart mode.  程序以智能模式启动
// "Active=3" program will come up in manual mode.  程序以手动模式启动

Active=1

// -----------------------------------------------------------------
// manual fan speed at program start
// 程序启动时,手动风速的初始值.(*我发现我的T61上,64风速是最快的*)

ManFanSpeed=7
 
// -----------------------------------------------------------------
// Program exits manual mode and switches to smart mode with last chosen
// profile, if this temp (degrees Centigrade or Fahrenheit) is achieved.
// default= 80 degrees Centigrade / 176 degrees Fahrenheit.
// 当温度达到该值时,程序将自动退出手动模式,并切换到之前启用过的智能模式.

//ManModeExit=55     //ManModeExit=131   // with Fahrenheit
ManModeExit=55 

// -----------------------------------------------------------------
// Window stays on Top if StayOnTop=1, normal behavior =0
// 窗口是否一直前置显示,1为前置,默认为0,不前置.

StayOnTop=0
	
// -----------------------------------------------------------------
// Set to 1 for slim widget
// 1为窗口细长型显示,0为窗口粗矮型显示,显示的信息量相应的多一些.

SlimDialog=1   
 
// -----------------------------------------------------------------
// set to 1 for bluetooth with enhanced data rate (i.e. T61,
// X61  for T4x, R5x set BluetoothEDR=0 )
// 设置为1时增强蓝牙的传输速率,例如T61,X61.但是对于T4x,R5x,请设置为0

BluetoothEDR=1
 
// -----------------------------------------------------------------
// Windows Priority of Process (0-5, normal=2), increase if fancontrol has 
// big delays in response while other processes consume performance.
// 程序的优先级,可以设定为0-5,正常是2,如果其他程序大量消耗系统资源导致TPFanControl有较大的延迟,请把这个数值加大.

ProcessPriority=5

// -----------------------------------------------------------------
// Show no icon ballons: NoBallons=1, show icon ballons: NoBallons=0
// 禁止托盘处的程序图标显示提示信息时,设为1,反之设为0.

NoBallons=1

// -----------------------------------------------------------------
// check temperatures every x seconds (default 5)
// 每隔x秒检查温度,默认是5.

Cycle=1

// -----------------------------------------------------------------
// For Thinkpads A2x,T2x,X2x set NoExtSensor=1 to exclude reading 
// of extended sensors to prevent program errors. Attention 570(E) 
// is NOT compatible. Fan speed is not available on all models.
// 对于Thinkpad A2x,T2x,X2x,设为1可以避免因读取不存在的温度传感器而导致程序出错.注意,570(E)是不兼容的.所有的机型上都无法设定风速.

NoExtSensor=0

// -----------------------------------------------------------------
// Minimize to systray immediately when starting
// 设定为1时,当程序启动后,立即最小化到托盘.

StartMinimized=1

// -----------------------------------------------------------------
// check icon of tpfcicon.exe (optional) every x seconds (default 1)
// 每x秒检查tpfcicon.exe的图标(可选,默认是1秒).

IconCycle=1

// -----------------------------------------------------------------
// Show new icon with max. temperature / sensor name
// 显示最高的温度和芯片的名称

ShowTempIcon=1

// -----------------------------------------------------------------
// Save the icon by a start delay of the program/service of 
// "SecStartDelay" (sec.) within "SecWinUptime" (sec.) after (re)boot
// Delete slashes '//' at next 3 parameters.
// 在启动或重启后,设定程序的延时启动时间,将下面的'//'删掉就能启用(*这个没啥用,我不弄的*)
// 
//SecWinUptime=120	//"SecWinUptime" (sec.) after (re)boot
//SecStartDelay=60	//start delay of the program (sec.)
//NoWaitMessage=0	//set to 1 to avoid sleep message

// Notice: Only Support TPFC v0.63 Setting
//ReIcCycle=600		//rebuild TempIcon every xxx secs.

// -----------------------------------------------------------------
// Temperature thresholds for turning the taskbar icon
// yellow orange red (Smart and Manual mode only and
// only together with MinimizeToTray=1)
// 对于不同的温度,系统托盘所显示的颜色,黄,橙,红.仅在智能和手动模式下生效,并且MinimizeToTray=1

//IconLevels=65 75 80    // Fahrenheit: IconLevels=122 140 158
IconLevels=50 60 65 

// -----------------------------------------------------------------
// Beep frequency and duration (in ms) for successful
// fan state changes. (Set either or both to zero to 
// disable)
// 当成功转换风扇状态时,蜂鸣器的频率和时长(毫秒),任何一个值设定为0时,禁止蜂鸣.

FanBeep=0 0

// --------------------------------------------------------
// If this max number of consecutive EC read errors occur
// program will switch fan back to bios mode and exit
// 当读取温度传感器的错误次数达到改设定值后,程序将自动切换到bios控制并退出.

MaxReadErrors= 10

// --------------------------------------------------------
// Log2File=1 enables, Log2File=0 disables writing to TPFanControl.log
// Start program with admin rights.
// 允许或禁止写入日志文件,这个需要管理员权限

Log2File=0

// --------------------------------------------------------
// Log2csv=1 enables, Log2csv=0 disables 
// writing to TPFanControl_csv.txt renamed to 
// TPFanControl_last_csv.txt after restart of TPFanControl
// rename to *.csv for use with excel
// Start program with admin rights.
// 设定为1时,允许日志写入TPFanControl_csv.txt,程序重启后,自动更名为TPFanControl_last_csv.txt.将扩展名改成.csv时,可以用excel打开.(*这个需要在文件夹选项中,将"隐藏已知类型的扩展名"后面的勾去掉才能显示并更改扩展名*)

Log2csv=0

// --------------------------------------------------------
// List (separated by comma) of sensors to ignore when
// determining the max. temperature.  (Use lower case,
// e.g "IgnoreSensors=pci,aps")
// 判断最高温度时,哪些芯片是不受监控的(相当于黑名单,多个名称用逗号隔开,并用小写字母).

IgnoreSensors=aps,crd,bat,bus,pci,pwr
// (*我的T61有显卡门,所以只监控gpu的温度,除了gpu,其他所有的芯片都列上去了.大家可以把cpu从黑名单中删除*)

// ---------------------------------------------------------
// List of new 3 letter sensor names, delete leading 
// slashes to activate. Don't use capital letters for readability 
// of temp icon.
// 写3个新的字母来重新命名芯片的名称,把'//'删除就能启用.别用大写字母

//SensorName1=cpu
//SensorName2=aps
//SensorName3=pcm
//SensorName4=gpu
//SensorName5=no5
//SensorName6=x7d
//SensorName7=bat
//SensorName8=x7f
//SensorName9=bus
//SensorName10=pci
//SensorName11=pwr
//SensorName12=xc3

// ---------------------------------------------------------
// calculating Highest Temp with: 
// temperature of sensor no. = real temp minus SensorOffsetno.
// Default SensorOffset1-12=0 , Capital O in SensorOffset,
// to activate delete slashes '//',
// Negative SensorOffsetno. values increase temperature values.
// 重新计算最高温度,传感器温度=实测温度-偏移量,默认的偏移量都为0,删除'//'可以启用计算.当偏移量为负数时,则增大温度值

//SensorOffset1=20
//SensorOffset2=20
//SensorOffset3=0
//SensorOffset4=2
//SensorOffset5=1
//SensorOffset6=5
//SensorOffset7=5
//SensorOffset8=4
//SensorOffset9=3
//SensorOffset10=2
//SensorOffset11=1
//SensorOffset12=5

// -----------------------------------------------------------------
// set to 1 to show calculated temps for sensors
// 设定为1时,显示计算后的温度值

ShowBiasedTemps=1 

// -----------------------------------------------------------------
// Show all/active sensors at start up. all=1 only active=0
// 在启动时,显示所有/激活的传感器温度值,1为所有,0为激活的

ShowAll=0 

// --------------------------------------------------------
// temperature levels 'Level=' with associated fan levels
// (for the fan to come back, temperature must fall
// down to previous level).  There may be more or
// less levels in this list.  The first one should
// have a fan speed of zero and is the "turn off"
// temperature.
// Fan speed of 64 is extreme and may be an *unsupported*
// and *damaging* mode.  A fan speed of 128 setting is
// not really a fan speed in itself but will instead switch
// fan control to BIOS mode (0x80).  The idea of this
// is to let the program get out of the way and let the
// BIOS handle extremes.(and then switch back to smart if
// the temperature is okay again)

// Temp of lowest Level (commonly set to fan speed zero) of profile 
// "Smart Mode 1" will switch from Celsius to Fahrenheit if set higher 
// than 79 degrees. Temps of higher levels have no influence on F/C. 
//
// profile "Smart Mode 1"
// Celsius:         	// Fahrenheit: 

// change values and number of items for your needs
// !!!! "Level" FAN 0 > 80 -> switch to Fahrenheit !!!!

// Notice: Only Support TPFC v0.63 Setting
MenuLabelSM1=Smart Mode 1/  Label for Icon Menu, must be terminated by '/'

// (*智能模式1下的设定*)
// 
//Level=60 0		// Level=140 0
//Level=65 1		// Level=150 1
//Level=75 3		// Level=165 3
//Level=80 7		// Level=175 7
//Level=90 64		// Level=195 64

Level=30 0 
Level=40 1 
Level=45 4 
Level=49 7 
Level=52 64 
// (*这些是我的温度设定,分别设定了30°,40°,45°,49°,52°,可以自己改*)

// optional 2nd profile "Smart Mode 2", switched by icon menue
// change values and number of items for your needs
// to deactivate, insert leading '//' into following lines

// Notice: Only Support TPFC v0.63 Setting
MenuLabelSM2=Smart Mode 2/  Label for Icon Menu, must be terminated by '/'

// (*智能模式2下的设定*)
// 
//Level2=22 0		// Level2=70 0
//Level2=33 1		// Level2=90 1
//Level2=38 2		// Level2=100 2
//Level2=44 3		// Level2=110 3
//Level2=55 7		// Level2=130 7
//Level2=66 64		// Level2=150 64
//Level2=77 128		// Level2=170 128

Level2=30 0 
Level2=40 1 
Level2=45 4 
Level2=49 7 
Level2=52 64 
// (*这些是我的温度设定,分别设定了30°,40°,45°,49°,52°,可以自己改*)

// -----------------------------------------------------------------
// IconColorFan=1 digital Icon will turn green while fan is running. 
// 设定为1时,当风扇转的时候,图标为绿色

IconColorFan=1

// -----------------------------------------------------------------
// Lev64Norm=1 : Fan level 64 acts as normal level with hysteresis, 
// fan will run till next lower temp step is reached (no pulsing fan). 
// If set to zero fan level 64 acts as emergency level without hysteresis,
// fan will run till level64 temp is reached again (pulsing fan can happen).
// 设定为1时,最高风速有延迟效应,也就是说,当温度下降到最高档温度值以下时,风速仍旧为最高,直到继续下降到下一档温度时,才调低到下一档风速.如果设置为0,则一旦下降到最高档温度以下时,就立马降低到下一档风速,直到温度再次超过最高档温度值时再调高到最高风速.

Lev64Norm=1